. Determine the critical net area for the angle given in the figure if 16mm diameter holes are used. Area of the angle = 2,751 sq.mm., thickness: %3D 14mm 120m 0mm- 00mm 50mm 70mm

Q: The normal and shear stresses in a bar must be limited to omax and tmax. Each limit is used to…

A: Answer:-  A Option A " the larger area " is the correct answer.  Explanation:-  A designer must…

Q: Consider a cantilever beam ABC of the total length 'L' and a constant flexural rigidity 'El' in…

A: It is question of Deflection of Beams which comes under Solid Mechanics.

Q: 1. Determine the distance x to the center of mass of the homogeneous rod bent into the shape shown.…

A: in this question a curved rod is given and we are told to find verticle and horizontal reaction t…

Q: A constant-head permeability test was conducted on a soil specimen under a hydraulic gradient of…

A:

Q: For the truss and loading shown, determine most economical cross-sectional area (in in2) of member…

A:

Q: Figure Q1 shows a 10 kg large disc is placed in contact surface of wall B and surface C which both…

A:

Q: Water entering a pump through an 200mm diameter pipe at 27.6 kPa has a flow rate of 0.1 m^3/s. It…

A:

Q: ly- f= 6,000 psi • As = 7.07 in? • b = 16 in • d= 30 in a) Compute the depth of the compressive…

A:

Q: Calculate the volume and surface area of a solid cylinder 1.5 m diameter and 2.5 m tall.

A: Given- Solid cylinder-Diameter d=1.5 mHeight h=2.5 m

Q: A sand layer found at sea floor under 20 m water déptri is characterized with relative density =…

A:

Q: 1. The accompanying tabulation gives elevations of points over the area 30m by 30m city lot. The…

A:

Q: Solve 5 problems (following the conditions stated below) involving the use of shear and moment…

A: Note : since you have posted multiple problems, as per your choice, I solve 1st problem for you.…

Q: 1311. The triangular plate ABC in Fig. P-1311 moves so that its vertices A and B slide on the…

A: "Since you have posted multiple questions. We will solve the first question for you." Solid…

Q: 1. When two grades meet at the valley and the curve will have a convexity downwards. a. Summit b.…

A: As per company's guidelines we can only answer first three questions. Kindly post other questions as…

Q: A 0.325 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 12.0 in.,…

A:

Q: 2. Another reinforced concrete beam has the following properties: • fy= 60 ksi • f= 5,000 psi • As =…

A:

Q: Current Attempt in Progress A beam is subjected to equal bending moments of M, - 3900 N m. The…

A:

Q: 0.5 cm 5cm water Linseed oil (SG=0.92) 10cm T//////

A:

Q: Q1 A soil meant for road construction is said to have a CBR of 5% explaining the meaning behind this…

A: Three questions has been asked, as per guidelines the first question is answered here. CBR means…

Q: The boom AC is a 4-in. square steel tube with a wall thickness of 0.25 in. The boom is supported by…

A:

Q: Between a plate and the body of a bolt or a pin, the average bearing stress is computed by dividing…

A: Bearing stress may be defined as the contact pressure between the seperate bodies

Q: Solve and show complete solution. From the technical description below, what is the coordinates of…

A:

Q: simply supported beam to carry a uniformly distributed load of intensity

A:

Q: Constant head permeab on two soil specimens, S1 and S2. The ratio of height of the two specimens…

A:

Q: PROBLEM 01: Given the figure below, (a) determine the value of h in the siphon shown if velocity at…

A: step 1-

Q: A 0.400 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.9 in.,…

A:

Q: The two pieces of wood, 2.62in. by 4.37 in., are glued together along the 510joint. Determine the…

A:

Q: The fixed-end member shown in Figure P6.6-13 is a W18 x 71 of A992 steel. Bending is about the…

A: For A992 steel fy = 50ksi

Q: A simple beam with an overhang is subjected to a point load P = 16.5 kN. P A B L -L- If the maximum…

A:

Q: Calculate straight line equation for following Transportation data Road Length, X (km) Number of…

A: Given table is about the road length in Km and number of vehicles on that span of road

Q: Problem: A gravity dam in the figure carries water that is 12 m deep on its upstream side. The…

A:

Q: One MPa is equivalent to one N/m?. A) True B) False

A:

Q: The table below shows the laboratory results of the sieve analysis of Soil A and B. What is the…

A:

Q: Consider the beam and loading shown. Assume that E=200 GPa and I=38x106 (mm4). P=2.3 kN and L=2.2 m,…

A:

Q: A stainless steel tube with an outside diameter of 56 mm and a wall thickness of 5 mm is used as a…

A: Load = stress * Area

Q: 0.5 in. B 1.8 in. P - 0.5 in. A 60° 1.8 in. 45° C

A:

Q: Shear stress is always maximum on the planes of maximum or minimum normal stress. (A) True (B) False

A: Given  Shear stress is always maximum or minimum on the plane of maximum or minimum normal stress.…

Q: igure shown, A, D, tion of a sounding vessel which is to be located. If b = 6,925.50m, C = 6,708.4 e…

A: To find angle X and Y

Q: deten miue Tloege teal steed aree cenerete blede incles =6e Jes)

A:

Q: agrams for the beam shown below. 10 kN p= 20 kN/m

A:

Q: E6 = 134.3 g E8 = 134.8 g E12 = 52.5 g 1_Calculate the moisture %3D content 2_field density

A: The moisture content of the soil or water content of the soil is defined as the ratio of the weight…

Q: A trapezoidal weir having side slope of 1H to 2V discharges 50 m3/s under a constant head of 2m.…

A:

Q: Refer to the photo provided and please make sure your handwriting is readable. L1 = 2.02 m L2 = 1.21…

A:

Q: Discuss the following items briefly. 1. How is a meter defined by a standard? 2. Describe how…

A:

Q: 1. Two tangents intersect at an angle of 42° are to be connected by a intersection to the point of…

A:

Q: Problem: A gravity dam in the figure carries water that is 12 m deep on its upstream side. The…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Consider the beam with overhanging ends loaded by the three concentrated forces as shown. The beam…

A:

Q: Example 7: Determine the factor of safety of the bottom against heave for the very long braces…

A:

Q: A 0.500 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.3 in.,…

A: L=9.2in P=57lb

Q: 3. A 24 ft long, simply supported beam carries only a uniform live load (WL). The beam has the…

A: Answer We are given  Beam span = 24 ft fy = 60 ksi f'c = 3 Ksi b = 14 in d = 26 in h = 30 in Steel…

Errors in surveying

An error in surveying is defined as the difference between two or more values of an identical quantity. However, the estimates are never accurate and there will always be a degree of variability regardless of the research tool or method used. These differences are known as errors that need to be reduced or eliminated to maintain certain levels of accuracy. Even if you carefully follow the prescribed test procedures, the considerations may contain errors.