.Connect the 10 chm resistor in parallel with A & B the remaining resistors connected in series, the series combination is connected in parallel to the 10 ohm resistor and parallel to terminals A and B of the circuit shown in Fig. 3-14. 5. the AO. 202 10 30 BO Fig. 3-14 3-13, 6. Calculate the equivalent resistance of the .series-paraliel circuit shown in Fig. 3-14. R %3D equivalen: (calculated)

.Connect the 10 chm resistor in parallel with A & B the remaining resistors connected in series, the series combination is connected in parallel to the 10 ohm resistor and parallel to terminals A and B of the circuit shown in Fig. 3-14. 5. the AO. 202 10 30 BO Fig. 3-14 3-13, 6. Calculate the equivalent resistance of the .series-paraliel circuit shown in Fig. 3-14. R %3D equivalen: (calculated)

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 12PP: In an R-L parallel circuit, ET=480 volts, R=16, and XL=24. Find PF.

See similar textbooks

Similar questions

45 Which of the statements for the circuit below are correct? Thanks to I- C1 and C2 capacitors, the voltage gain of the circuit increases. Capacitors II - C1 and C2 are coupling capacitors and provide isolation function between AC and DC voltages in the oudut of circuit. thithe Thanks to III - RE resistance, the voltage gain of the circuit increases. Thanks to the IV - RE resistance, the stability of the circuit increases. V- C3 Capacitor is a bypass capacitor and prevents loss of voltage gain. Capacitor VI - C3 is the coupling capacitor and has no effect on the voltage gain in the circuit. VII - The greater the value of the source internal resistance Rs, the lower the voltage gain. VIII - The greater the value of any RL load to be added to the circuit, the lower the voltage gain. Vcc Rc R1 C2 B RE Please choose one: O a. III, IV, V, VI and VII O b. II, III, IV, V and VII O c. I, II, III, IV, V, VI, VII and VIII O D. IV, V, VI, VII and VIII O to. I, II, III, IV, V, VI and VII O f. I,…
Q3) For the network shown in the figure below, determine the following: a) re b) Zini and Zinz c) Zoj and Zo2 d) Av1, Av2, and AvT +20 V 6.8 ka 30 kQ 6.8 ka 30 ka 0.5 pF 0.5 uF 1150 B-150 1.5 ka 50 uF 1.5 ka 50 uF
I want the solution Q2/ Q3/ Q4/
1. Using Series-Parallel concept, Find the following for the given circuit. The value of the power supply and resistances are given in Page-4. a) the current supplied by the source b) the voltage drops across each resistor c) the r dissipated by R3 R1=45kn R2=2kn R3=22kQ R4=14kn R5=17kn R6=85kn V1=24 v R₁ R₂ V₁ R₂ R₂ R₂
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
Two batteries, A and B, are connected in parallel and an 80 ohm resistor is connected across thebattery terminals. The e.m.f. and the internal resistance of battery A are l00V and 5 ohm respectively,and the corresponding values for battery B are 95V and 3 ohm respectively. Find (a) the value anddirection of the current in each battery and (b) the terminal voltage
Good Design Calculate the unloaded voltage Va in the following circuit. Record the calculated value in the table below. Construct the circuit using MultiSim. Energize the circuit and measure V2. Record the measured value in the table below. De-energize the circuit. Assume a 30-ka load resistor is added to the circuit as shown. Calculate the loaded voltage Viz. Record the value in the table below. Construct the circuit using MultiSim. Energize the circuit and measure Via. Record the measured value in the table below. De-energize the circuit. Parameter Calculated (V) Measured (V) Va
Consider the series-parallel circuit shown in the figure below with various multimeters connected in the circuit. Assum that XMM1 has been configured in ammeter mode, and XMM2 has been configured in voltmeter mode. XMM1 R1 1kQ XMM2 R2 R3 V1 1kQ 1kQ 12V 3.1: Redraw the circuit replacing XMM1 and XMM2 by their equivalent circuit models 3.2: Assume that XMM2 was incorrectly configured in ammeter mode. Redraw the equivalent circuit from 3.1 and compute the current that would be measured by the ammeter in this scenario. Hil-
To measure the change in resistance of the gage(s) and indicate the location of the gauge on the beam, construct the Wheatstone bridge circuit. Calculate the Wheatstone bridge output if the gauge indicates a strain of 4000.then,Evaluate how can the number of strain gauges affects your measurement result. Justify your response with a calculation and a diagram showing the gage's placement on the beam.
Referencing to the components connected on the breadboard below, draw the equivalent circuit schematic. 24 V R3 • . . o .. • . o o .. R4 • . O O 0 O O o o O o o O. O o o o o O o o o O o o Oooo o o OoO • 0 o o O0 o o o o o 0 Oo O O o o O o
INSTRUCTIONS: Solve the following problems. Show and COMPLETE solutions. Draw all CIRCUIT DIAGRAMS or the equivalent circuit (dummy circuit) as the case may be. Write your solutions on sheet/s of short bond paper. A battery is to consist of 20 identical cells. The emf of each cell is 1.5 V and the internal resistance is 0.20 ohm. This battery will be used to supply power to a 10 ohm lamp. Determine the current on the lamp if:1. The 20 cells are connected in series 2. The 20 cells are connected in parallel 3. The 20 cells are arranged 5 cells in series in 4 parallel rows.
(e) Create a list of components for the following circuit. 6v Vcc D1 R7 4k7 ZS D2 ( M RV1 470k C1 100nF 10µF C2 IC1 R2 150k RS Q4 Q5 Q4-Q14 R5 Q1 Q6 4. Q7 4k7 10 14 13 15 RTC Q8 Q9 4060 Q10 Q12 Q13 Q14 стс R1 100k _12 MR R4 4.7k R6 4.7k LED1 LED2