1. Figure 2 shows an operational amplifier. A voltage of 2 V is connected to the inverting input Vref as voltage offset. The circuit should have a 5 V power supply connected to the positive power rail (+Vcc) and the negative power rail (-VEE) to ground. Vref +Vcc -VEE Figure 2. Vo a) Compute Vo when Vi is supply with a DC voltage input, varying from -5V to +5V. Sketch the graph with Vi as the x-axis and Vo as the y-axis.

1. Figure 2 shows an operational amplifier. A voltage of 2 V is connected to the inverting input Vref as voltage offset. The circuit should have a 5 V power supply connected to the positive power rail (+Vcc) and the negative power rail (-VEE) to ground. Vref +Vcc -VEE Figure 2. Vo a) Compute Vo when Vi is supply with a DC voltage input, varying from -5V to +5V. Sketch the graph with Vi as the x-axis and Vo as the y-axis.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.20P: A circuit consists of two impedances, Z1=2030 and Z2=2560, in parallel, supplied by a source voltage...

See similar textbooks

Similar questions

Electrical Engineering (25) It seems that a suburant in the negative impedance converter is the one that simulates negativity for a given floating impedance. Explain how the indicated subar- cuit operates.
In the given figure Find V0 ?
2. The circuit given below is using a transformer of 230V/30V. The load resistance is 10KS. Find Vin (rms and peak values), Vdiode and VLOAD (Peak and dc values). Draw the input and output voltage waveforms. (Si diode) Vin: Vin rms= Vin peak = VDIODE Vdiode = 4 Vin VLOAD: VLOAD Peak =. Load VLOAD VLOAD DC= 2031 Supply wwwwww
A2 Consider the circuit in Figure A2 where Vs = 12 V, R₁ R₂ and the input is a sinusoidal signal with peak voltage of 35 mV. Draw a plot of the signal against time that you expect to measure at the output and explain how the circuit functions. +Vs R₁ R₂ Vout Vret Hi Vin + Ao -Vs Figure A2
In the common mode, ..... ..... ..... Select one: a. the output signal are in-phase b. an identical signal appears on both the inputs c. the outputs are connected together d. both inputs are grounded
this is electric circuit questin ...plz solve it early .plz solve early
Home work: Zener regulator have input voltage vary from 15V to 20V and load current vary from 20mA t0 100mA. Find the limited resistor to be connected in series if the voltage Vz = 10V.
2.0 a. TMP35 b. TMP36 c. TMP37 +Vs - 3V Using the appropriate curve, develop a linear equation for the output temperature as a function of voltage. 1.8 1.6 E 1.4 1.2 1.0 0.8 0.6 0.4 0.2 -50 -25 25 50 75 100 125 TEMPERATURE (*C) Figure 6. Output Voltage vs. Temperature OUTPUT VOLTAGE (V) 200-20C 00
In circuit shown in figure, the operating point is chosen such that = 9V and ß = 49 Ic 1.75mA, VCE = 3.1V,If Rc = 2.7KN, Vcc %3| Determine the values of R1, R2 and Rg [VBe = 0.3V and I = 10ß] RC R1 = Vcc RE R2 www www www www
for The Circuit shown in figure if CB = 50) find The values of CIe). and of Then express The c hamge in value by apercentage + 15レこ RB2 = so KQ RE 3K52
Figure shows a transistor switching circuit. Find the Vcc and Rc, which causes the output voltage to have a peak to peak value of 6V (given that the input voltage signal Vi, and the output voltage signal Vo, have units of Volt) Fone: V₁ 10k2 www +Vcc Rc V₂ B-100
DC to AC 1) Determine the efficiency of the following DC to AC converter (i.e. how much of the energy is in the Ist harmonic?). (on for 10ms (+20V), off for 20ms, on for 10ms (-20V), off for 20ms, repeat) +20V 20ms 20ms 10ms ov 10ms -20V 1) Determine the efficiency of the following DC to AC converter (i.e. how much of the energy is in the Ist harmonic?). +2-V -20V 10ms 20ms Oms 30ms 40ms