2. A steel shaft (G = 80 GPa) of total length L = 3.0 mis encased for one-third of its length by a brasssleeve (G, = 40 GPa) that is securely bonded to the%3D%3Dsteel. The outer diameters of the shaft and sleeveare di = 75 mm and d2 = 90 mm, respectively. Themaximum shear stress in brass is 70 MPa, maximumshear stress in steel is 110 MPa and the maximumallowable angle of twist is 5°. What is the maximumallowable torque that can be applied at the ends ofthe shaft?BrassSteelshaftdi = 75 mmd2 = 90 mmsleeveTTAB1.0 m-L= 2.0 m-2= 2.0 md1dyBrass-sleeveSteelshaftd2d2

Given, Steel shaftGs=80 GPa Total length L=3 m Gb=40 GPa Diameter, d1=75 mmd2=90 mm Shear stress in…

2. A steel shaft (G, = 80 GPa) of total length L = 3.0 m is encased for one-third of its length by a brass sleeve (G, = 40 GPa) that is securely bonded to the %3D steel. The outer diameters of the shaft and sleeve are di = 75 mm and d2 = 90 mm, respectively. The maximum shear stress in brass is 70 MPa, maximum %3D shear stress in steel is 110 MPa and the maximum allowable angle of twist is 5°. What is the maximum allowable torque that can be applied at the ends of

2. A steel shaft (G, = 80 GPa) of total length L = 3.0 m is encased for one-third of its length by a brass sleeve (G, = 40 GPa) that is securely bonded to the %3D steel. The outer diameters of the shaft and sleeve are di = 75 mm and d2 = 90 mm, respectively. The maximum shear stress in brass is 70 MPa, maximum %3D shear stress in steel is 110 MPa and the maximum allowable angle of twist is 5°. What is the maximum allowable torque that can be applied at the ends of

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8 ksi, oy The normal stresses at a point in a steel member are ox 10 ksi. Using E -4 ksi, 29 x 103 ksi and v = 0.3, determine the normal strains at 2.31 %3D and oz this point. %3D ר- The rectongulor block, of material of€ length Land cross sectional ore 1 fits
The following steel member is connected to the gusset plate via two longitudinal welds. The width of the member is 58 mm and the length of the weld is 87 mm. The yield stress is 300 MPa and the ultimate stress is 675 MPa. The gross area of the member is 700 mm^2 . a. What is the tensile design yield strength in KN? b. What is the tensile design rupture strength in KN? c. If a tensile load of 85 KN is requiredfor the member, what is the minimum factor of safety for the steel member?
The 200-mm square aluminum block supports a compressive load of 300 kN. What is the normal stress acting on section a–a in MPa What is the shearing stress acting on section a–a in MPa The lapbelt assembly is to be subjected to a force of 800 N. What is the required thickness t in mm. of the belt if the allowable tensile stress for the material is 10 MPa?
1.(e) The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests. It has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑Y 40 MPa 80 MPa 25 MPa
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
O Compute the maximum value of P that will not exceed a stress of bronze of 100 MPa. Bronze A=450 mm2 A=600 mm Aluminum Steel A=300 mm 2 Compute the max. value of P that will not exceed a stress of E-83 GPa E=70 GPs E=200 GPa aluminum of 90 MPa. 600 mm 1,000 mm 800 mm 3Compute the maximum value of P that will not exceed a stress of steel (3) of 140 MPa.
Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E = 105 GPa) Aluminum plates (E = 70 GPa) Rigid end plate 300 mm 60 mim 40 mm
3. A steel baris l0mm diamelex and am lo It is stretched with a force of 20kN and exteads by 0-2mm- Calaulale e stress and strain.
A brass (? =5.6 ? 10^6 ???) and aluminum (? = 3.7 ? 10^6 ???) cylinders are bonded together at B, and are attached to fixed supports A and C. Determine (a) The torsion in AB, (b) The torsion in BC, (c) The maximum shearing stress in AB (d) The maximum shearing stress in BC.
The total tensile load of 160kN of a steel is to be stress at the middle portion limited to 150 N/mm2, find the diameter of the middle portion and also the length of the middle portion if the total elongation of the rod is to be 0.2mm. consider the young modulus of a steel.
Problem 2: A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel Bronze 480 mm² 650 mm² 3P 1.0 m 4P 2.0 m Aluminum 320 mm² 1.5 m 2P
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :