2. An electric vehicle is designed for a top acceleration off the line (from standstill) of 2.0 m/s². Assuming the electric motor's maximum torque is independent of speed, what is the vehicle's top speed while going up an 8% grade? Specs: Cr =0.02, Ca =0.3, m 1500 kg, Frontal cross-sectional area 2.5 m2. %3D

2. An electric vehicle is designed for a top acceleration off the line (from standstill) of 2.0 m/s². Assuming the electric motor's maximum torque is independent of speed, what is the vehicle's top speed while going up an 8% grade? Specs: Cr =0.02, Ca =0.3, m 1500 kg, Frontal cross-sectional area 2.5 m2. %3D

Name: 2. An electric vehicle is designed for a top acceleration off the lin
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 2. An electric vehicle is designed for a top acceleration off the line (from standstill) of 2.0 m/s?.Assuming the electric motor's maximum torque is independent of speed, what is the vehicle'stop speed while going up an 8% grade?Specs: Crr 0.02, Ca

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter3: Basic Theories And Math

Section: Chapter Questions

Problem 3RQ: Explain Newtons second law of motion and give an example of how this law is used in automotive...

See similar textbooks

Similar questions

H.W.1 Honda CR-V is a midsize SUV car with m= 1550 kg, l= 2620mm Assume a, = az, h= 720mm, Hy= 0.8 determine the maximum acceleration of the car and minimum time for 0-100 km/h if a) the car is rear-wheel drive. b) the car is front-wheel drive. c) the car is four-wheel drive. H.W.2 RoadRazer is a light weight rear-wheel drive sportscar with m = 300 kg, 1 = 2286 mm, h = 260 mm Assume a, = az. If the car can reach the speed 0- 100km/h in t= 3,2 s, what would be the minimum friction coefficient?
Describe Newtons first law of motion and give an application of this law in automotive theory.
Block of mass m=50 g, slide down on inclined plane with angle 0 = 60what is the acceleration of the object: a mg :Select one a. 5 cm/s? b. 1000 cm/s? c. 5/3 cm/s? d. 500 cm/s? e. 500/3 cm/s2 أخل اختياري
The motorcycles mass: 170 kg The drivers mass: 64 kg I1= 0,26m I2=0,19m a) What is the needed acceleration so the front wheel will lift from ground? b) What is the needed supporting force on the rear wheel (in the cituation above)? c) What is the needed friction force (in the cituation above)? d) What is the friction coeffiecient (in the cituation above)?
What is the value of acceleration due to gravity?
(2) lahai Q1-e) Kinetics: is used to predict the motion caused by given forces or to determine the forces required to produce given motion True False
Problem Solving: )An object falls from rest in a medium offering a resistonce. The velocity of the object hefore the ohject reaches the ground is given by the differential egua- tion dv/t + V% = 32, t/sec. uhat is the veloaty of the okject one second after it falls ?
(b) Table Q2(b) shows the information of a front-drive vehicle parameters. Table Q2(b): Vehicle parameters No Parameter Weight at front axle Weight at rear axle Value 1. 8,674 N 2 5,115 N 3 2.667 m Wheelbase CG height Coefficient of friction 4 0.4826 m 0.62 1.524 m Tread Final drive ratio 6. 7 3.70 0.319 m 1288 Nm/deg 840 Nm/deg 8. Tire size Roll stiffness at front axle Roll stiffness at rear axle 10 (i) Determine the maximum tractive force with locking differential (independent front suspension) in unit N. (ii) Based on Question 2 (b)(i), determine the maximum longitudinal acceleration of the vehicle in unit m/s?.
Scenario 1 Your boss, Melon Usk, wants you to determine the acceleration of his new car. The details of the car are as follows: The car's total mass is 1500 kg The motor outputs a constant torque of 300 Nm The drive train has a gear ratio of 10:1 to the drive axle Prior to any gearing, the motor and drivetrain have a moment of inertia of 0.5 kg m². The four tires are 0.6 m in diameter. A single set of final gear, drive axial, and tire has combined moment of inertia of 0.6 kg m². Not knowing how to proceed, you e-mail your favourite ex-instructor, Frank. He is very busy but draws you the following: ● ● ● ● ● ● Motor ● FT+ IM = 0.5 kg. m² TIN = 300Nm TIN Final Gear + Wheel Wheel RG Final Gear C Rw Fw Iw = 4(0.6 kg m²) = 2.4kg. m² RG = 10R Rw = 0.3m Car Fw m = 1500kg y x Frank also notes the following: You can treat all four tires, axels, and final gears as a single entity. The moments of inertia will add together but the radius will remain the same. You do not need to know the complex…
1. The car engine has a torque of 0.4 kNm at 2000 rpm (rev/min). What is the power (kW) at this time?
A body (150 kg) moves with a 40 m/sec, the kinetic energy equals to 120 kJ *True or False???
A completely automated Tesla travels up a 3% incline at 30 mph on a road that has good, wet pavement. The car has a wheelbase of 120 inches and a center of gravity that is 55 inches behind the front axle and at a height of 20 inches. The braking efficiency is 88%. It notices a pothole 35 ft ahead of the car and comes to a complete stop. a) Calculate the percentages of braking force that should be allocated to the front and rear brakes to ensure that maximum braking forces are developed. b) Will the car hit the pothole if it has (i) no antilock brakes and (ii) antilock brakes (braking efficiency 100%)? Assume theoretical stopping distance and neglect aerodynamic resistance.