3. For the following circuit: a. Calculate the impedance seen by the source in rectangular and polar form. b. Calculate phasors VI and v2 in polar form using voltage divider. c. Calculate the phasor Iin polar form. d. L = 5.3mH, what is the frequency of the source? e. How much is vi(t)? + V₁ j2 169/10° Vlin 1000V2

3. For the following circuit: a. Calculate the impedance seen by the source in rectangular and polar form. b. Calculate phasors VI and v2 in polar form using voltage divider. c. Calculate the phasor Iin polar form. d. L = 5.3mH, what is the frequency of the source? e. How much is vi(t)? + V₁ j2 169/10° Vlin 1000V2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The source in the circuit shown is a sinusoidal source. The supply voltages across various elements are marked in the figure. The input voltage is: 3V- ww -14 V-10V moon It
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power factor is ________. Hint: Draw the circuit and get Vs and Is
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
An inductive impedance made up of a resistor and an inductor has the characteristic that its currentadvances in phase to the voltage at the impedance A) lags in phase with the voltage across the impedance B) is in phase with the voltage across the impedance. C) None of the above
A 15ohms resistor connected in parallel with an impedance of 8 - j2 across an AC source. The entire circuit takes a total average power of 2000 watts. What is the average power in the 15ohms resistor?
Please show your detailed solution Number 14 The current in a series inductive circuit is 7.5 A at 25 Hz. The circuit takes 425 W, and the power factor is 0.47. The resistance of the circuit is A. 7.32 ohms C. 7.98 ohms B. 7.86 ohms D. 7.56 ohms
4- A Circuit of zero lagging power factor behaves as a. A capacitive circuit b. An inductive circuit c. RC circuit d. RL circuit
ESSAY: Describe what happens to the power in this RLC series circuit as the capacitance decreases. Explain in general terms why the observed change should occur. Understand the effects of basic electrical components on the average power of the system and the concept of power factor. Differentiate between average power and real power.
1) Two identical voltage waveforms of difference phase angles are shown in Figure B. Write down the expression of waveforms A and B clearly. HUS Voltage (V) 8 0 K/N B 7: ST ot
Draw phasor diagrams for the following: