3. The hydraulic cylinder Cextends and causes the collar A to move and accelerateto the left.3) If the length /= 1.5 ft, the angle 0 = 36°, the linear velocity of collar A, Va is 3.2ft/s, and the linear acceleration of collar A, aa is 2.4 ft/s?, determine the magnitudeof the angular velocity, WAB, of rod AB. Please pay attention: the numbers maychange since they are randomized. Your answer must include 2 places after thedecimal point, and proper unit.yYour Answer:Answerunits

Answered: Image /qna-images/answer/b6edbeee-270e-4b47-a3a1-1d2dbd0caf37.jpg

3. суinde extends and causes the coOllar A to move and accelerate to the left. 3) If the length / = 1.5 ft, the angle 0 = 36°, the linear velocity of collar A, VĄ is 3.2 ft/s, and the linear acceleration of collar A, aa is 2.4 ft/s², determine the magnitude of the angular velocity, WAB, of rod AB. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. y Your Answer: Answer units

3. суinde extends and causes the coOllar A to move and accelerate to the left. 3) If the length / = 1.5 ft, the angle 0 = 36°, the linear velocity of collar A, VĄ is 3.2 ft/s, and the linear acceleration of collar A, aa is 2.4 ft/s², determine the magnitude of the angular velocity, WAB, of rod AB. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. y Your Answer: Answer units

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The center O of the disk has the velocity and acceleration as shown in the figure. If the disk rolls without slipping on the horizontal surface, determine the velocity and acceleration of point B at the instant shown. Point A is not assigned for this problem, but if asked, could you find its velocity and acceleration, too? 5 m/s² A 45° 0 B 0.2 m 0.2 m' 3 m/s y
For the following mechanism, rod AB is pinned to the two disks at point A and point B, and the two disks roll to the left without slipping. if the length of rod AB, I= 2.4 m, and its angular velocity @ = 6.2 rad/s, determine the magnitude of the linear velocity of point B. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. (0.5 m 0.5 m No slipping No slipping Your Answer: Answer units
4. 4) The hydraulic cylinder Dextends, moves the rigid rod ABC, and causes the collar A to move with velocity and acceleration both to the left. If the dimensions/₁ 1.0 ft, and /2 = 2.0 ft, vµ = 5.5 ft/s, aµ = 2.1 ft/s², and the angle 0 = 30°, determine the angular acceleration (in rad/s²) of rod ABC. Negative sign must be included if the angular acceleration is clockwise. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Your Answer: 1₁ Answer B 12 ÏÏ a =
3. The hydraulic cylinder C extends and causes the collar A to move and accelerate to the left. 5) If the length /= 1.6 ft, the angle = 24°, the linear velocity of collar A, VA is 3.4 ft/s, and the linear acceleration of collar A, a is 3.2 ft/s², determine the angular acceleration in rad/s², & AB, of rod AB. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. y X B C Your Answer: Answer Ꮎ Ө A VA dA
3) Link AB of a robotic arm is rotating at a constant speed of 4 rad/s, while link BC is rotating at 5 rad/s, a speed that is increasing at the rate of 2 rad/s². Find the magnitudes of the velocity and acceleration of point C when AB is vertical and BC is horizontal, as shown here. 2.0 ft 1.5 ft B WAB A WBC = 5 rad/s αBC = 2 rad/s² = 4 rad/s C
Problem (4) In the mechanism shown, VA = 15 m/s with direction downward. Draw the velocity diagram, and determine the velocity of point D and angular velocity of link 5. Assuming that v4 is constant, draw the acceleration diagram and hence determine a3, as, ac, and ap. 2.05" A₂ 3 = 15 m/s B AC 2.4" BD = 3.7" BC = 1.2" -2.4" 5 45° --- -X DOL
The rod AB, shown in the figure, can slide freely along the floor and the inclined plane. At the instant shown, the velocity of end A is 1.4 m/s to the left. (a) Show that the magnitude of the rod's angular velocity is 3 rad/s and indicate its direction. (b) Calculate the velocity of end B and express it in vector form using rectangular (Cartesian) components. 500 mm B 300 mm 125 mm
As the hydraulic cylinder rotates around O, the exposed length I of the piston rod is controlled by the action of oil pressure in the cylinder. The cylinder rotates at the constant rate Ô = (n/3) rad/s and I is decreasing at the constant rate of † =150 mm/s. 375 mm a) Calculate the velocity v of end B. b) Calculate the acceleration a of end B.
For the mechanism, shown on the figure, v-3 m/s, a, 8 m/s². AB=√2 m. Determine: a) linear velocity and acceleration of the point B b) angular velocity and angular acceleration of the body AB. 730⁰ A vi
4. 4) The hydraulic cylinder D extends, moves the rigid rod ABC, and causes the collar A to move with velocity and acceleration both to the left. If the dimensions 1 = 1.1 ft, and 2 = 2.3 ft, VA = 4.7 ft/s, aa = 2.7 ft/s², and the angle 0 = 25°, determine the angular acceleration (in rad/s2) of rod ABC. Negative sign must be included if the angular acceleration is clockwise. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. %3D 12 D а Your Answer: Answer
For the following mechanism, rod AB is pinned to the two disks at point A and point B, and the two disks roll to the left without slipping. if the length of rod AB, /= 2.1 m, and its angular velocity W = 4.5 rad/s, determine the magnitude of the angular velocity of link AB. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. 0.5 m No slipping Your Answer: Answer 1 units 0.5 m No slipping
1. At a given instant the bottom A of the ladder has an acceleration of 8 ft/s² and velocity of 10 ft/s both acting to the left, as the ladder slides down the wall. Determine the ladder's angular velocity and angular acceleration at this same instant. Also determine the acceleration of the top of the ladder, B. Show all work, list governing equations, label all coordinates. Gravity 30° 16 ft Ana PRE B