3.32. How far below the water surface should a vertical square, 1.22 m on a side with two sides horizontal, be immersed so that the center of pressure will be 76 mm below the center of gravity? What will be the total force on the square? Ans. 1.01 m, 23.7 kN

3.32. How far below the water surface should a vertical square, 1.22 m on a side with two sides horizontal, be immersed so that the center of pressure will be 76 mm below the center of gravity? What will be the total force on the square? Ans. 1.01 m, 23.7 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1.What are types to Design the Rigid pavement. 2. How these designs are differ to each other. 3.…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: Differentiate between generic diversity and cultural diversity

A: Answer - Genetic diversity is the differences of DNA among individuals of a particular species .The…

Q: Example: the low cycle fatigue of a certain steel is given by life cycle equation-2: (of/E)=0.005…

A: Given data:- The fatigue strength of steel σf/Modulus of elasticity(E), σfE=0.005 The fatigue…

Q: The velocity of a particle along the s-axis is given by v = 10s4/3 where s is in millimeters and v…

A: Given in the question:The velocity of a particle, v=10×s43's' is in mm,'v' is in mms,

Q: Q3: A// List a summery for the components of Nuclear power plant. B// The power delivered by the…

Q: A beam has a width of 275 mm and an effective depth of 500 mm. f'c = 28 MPa. Fy = 414 MPa, Es =…

Q: If the BOD of a municipal wastewater at the end of 7 days is 60 mg/L and the ultimate BOD is 85.0…

Q: A grade ascending at the rate of 6% meets another grade descending at the rate of 4% at the vertex…

A: Given G1= 6% G2= -4 %

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

Q: A clockwise traverse ABCDEA was surveyed Find the length and direction of line AD

Q: A groove is machined into the circumference of a steel shaft held in cantilever and supportin bevel…

Q: Differentiate between Environmental resources and Natural resources

Q: The wood beam supports loads of w = 480 lb/ft and P = 1200 lb on span lengths of LAB = 8.8 ft, LBc =…

Q: What does the pacer test look for?

A: Answer - The PACER fitness exam is an excellent method for encouraging kids to love exercise. It…

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I= 1730…

Q: The angle of curve is the angle between intersection of a 4

A: Using definition

Q: Using the analytical method of joints, determine the stress in the members of the truss shown. B…

A: GIVEN: TO FIND: Determine the stress in the members of the truss shown above. CONCEPT: Use method…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 60 MPa and…

A: Given Sx=60Mpa Sy=-215Mpa

Q: B-1 Draw the shear and moment diagrams for the beam. 10 KN 2m 10 kN/m m

A: Given:- A beam is given with:- The magnitude of the uniform load = 10 kN/m The magnitude of the…

Q: A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation…

A: Given, Q = 500 L/s Z1 = 65 m Z2 = 95 m

Q: Problem 2. . For the given truss all AE are constant. Using unit load method find a) Horizontal…

A: Given data AE = Constant

Q: A grade of vertical curve can expressed as be O O O OC O A-In terms of percent O D-Both A and B C-In…

Q: a. Determine the centroid of the composite figure. b. Calculate the moment of inertia with respect…

A: Given data:-

Q: shown. The diameter of the can is 9cm. what is its weight in Newtons?

Q: Determine the dimensions of a high rate trickling filter for the following data: (ii) Recirculation…

Q: The simply supported beam is loaded as shown in the figure. Determine the value of maximum…

A: Given A beam Required Maximum deflection

Q: slope. It has a side slope of 2:1 and the base width of the roadway is 12 m. (a) Compute the volume…

A: Side slope = 2:1 Base width = 12 m For station 10+110, Cross section…

Q: The beam shown in the Figure q2 below is a continuous beam of 2 spans. Determine the reactions at…

Q: If the fore bearing of a line is N 26°35' W, its back bearing will be N 26° 35' E O S 26° 35' WO S…

Q: A wood beam is strengthened using two steel plates as shown in the figure below. 1 -100 mm- q= 5.0…

Q: STRENGTH OF MATERIALS PLEASE WRITE THE SOLUTIONS LEGIBLY AND USE 4 DECIMAL PLACES. RATE WILL BE…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Trapezoidal formula is also known as Prismoidal method O Average end area method O Simpson's rule O…

A: Using definition

Q: 3. The pendulum consists of a 5-lb solid ball and a 2-lb uniform rod. If it is released from rest…

A: Given ::

Q: A clockwise traverse ABCDEA was surveyed Find the length and direction of line AD Length(m) 101.01…

Q: 3) An overhanging beam is loaded as shown in the figure. Using EI = 20.48x106 N-m², determine the…

A: Given data EI = 20.48 × 106 Nm2

Q: Trapezoidal formula is also known as 7 O Average end area method O Simpson's rule O Double-meridian…

Q: What sources of error ave been earthquake and the magnitude of characteristics/components that we…

A: Earthquake - it is shaking of surface of earth due to sudden release of energy in earth's crust, due…

Q: Calculate the closing error of the following traverse Line AB BC CD DE EA Length (m) 193.20 176.80…

Q: ACB is supported with a pin at A and an elastic steel rod at C. The elastic rod has a diameter of 26…

Q: ouble tee cross section is used for the beam shown below. Assume the following lengths and loads: 14…

Q: Factory of safety of rcc?

A: Safety factor or Factor of safety is very important term in designing and it determines how strong a…

Q: A cantilever beam supports the variable load shown. Calculate the supporting force RA and moment MA…

Q: Find the reactions at the support A and B in the system below. * A 2 m ,1 kN 600 -10 m- 500 N/m B

A: Answer Let us first draw free body diagram of the given beam as shown below Resolve the inclined…

Q: 3m A 12 kN -3 m 8 kN B F -3 m C -3 m- E D 5m

Q: 1- Find elevation of all points by rise and fall method and apply appropriate check.

A: Staff = 5m BM=Points 1 and 12=210 m and 212.55 m B.S I.S F.S Rise Fall RL Correction Corrected RL…

Q: Refer to the previous problem, determine the average time spent by the vehicles on the system…

Q: A force of 10,000 lb acts on joint D of a truss as shown. a) Determine which members of the truss…

A: This question is from structural analysis Here one Truss is given and we are asked to find out zero…

Q: It is anticipated that the filtration rate should increase with time.True or False?

A: Answer :- False It is anticipated that with increase in filtration rate the time will decrease.

Q: In a plate girder subjected to a bending moment of 200 kN-m, the width and thickness of flange are…

A: Given- Bending moment M=200 kN-mwidth b=200 mmthickness t=10 mmfy=250 MPa

Q: The extruded plastic shape has dimensions of D = 21 mm, d = 15 mm, a = 80 mm, and t = 4 mm. (a)…

Question

kindly give the exact and complete solution for this question where the asnwers are 1.01 m and 23.7kN

3.32.
How far below the water surface should a vertical square, 1.22 m on a side with two sides horizontal, be
immersed so that the center of pressure will be 76 mm below the center of gravity? What will be the total
force on the square? Ans. 1.01 m, 23.7 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

5. A plate in the shape of a triangle is submerged vertically and the base which is 3 ft long is in the surface of the water. Find the altitude of the triangle if the force due to the water pres- sure against the face of the plate is 50w where w is the weight per cu. ft. of water.
A swimming pool has a width of 12ft and a side profile as shown. Determine the resultant force the pressure of the water exerts on bottom BC. Inclined BC makes an 14.478 degrees with the horizontal.
Friction Problem 350kN A 350 kN block is resting on a rough horizontal surface for which the coefficient of friction is 0.45. Determine the force P required to cause motion to impend if applied to the block. A. Horizontally B. Downward at 30' with the horizontal. F N C. What minimum force is required to start motion?
1. Determine the minimum coefficient of static friction us which will allow the drum with fixed inner hub to be rolled up the 17° incline at a steady speed without slipping. What are the corresponding values of the force P and the friction force F? m 112 17° P 31°
(51) 5 m long AB rod is loaded with a 20.2 kN/m uniformly distributed load from End A to the midpoint as shown. The elastic modulus of the rod material is 210 GPa. The area moment of inertia of the rod is 837 cm. The slope at End B is most nearly: A. 0.55⁰ B. 1.25⁰ C. 1.50⁰ D. 2.00⁰ A 2.5 m 20.2 kN/m 5m B
A swimming pool has a width of 12ft and a side profile as shown. Determine the eccentricity e of the resultant force the pressure of the water exerts on bottom BC. inclined BC makes an angle of 14.478 with the horizontal.
An equilateral triangular plate of side 2.4m placed horizontally in a liquid (sp. gr. 0.80) in such a way that the center of the plate is 2.5m below the free surface of water. (a) Determine the area (in sq. meters) of the plate. (b) Determine the magnitude (in kN) of the resultant force on the plate.
A 400 kN block is resting on a rough horizontal surface for which the coefficient of friction is 0.40. Determine the force P required to cause motion to impend if applied to the block. 1400 F N. @. Horizontally 2 Downward at 30* with the horizontal O What minimum forçe is required to start motion?
4. If the coefficient of static friction M0.35, will the box move? S2N 20kg
1. A box resting on a floor is pushed by a horizontal force P and restricted by an inclined force Q, as shown below. The box has a weight W= 650 lb and the inclined force Q = 150 Ib. The coefficient of friction between the box and the floor is 0.45. How high above the floor can the force P act so that the box moves without tipping about Point D? [Friction Equation: F= uN] 45° A B 1'- 6 P. 3' - 0"
An equilateral triangle plate of side 2.4 m placed horizontally in a liquid (sp. gr. =0.80) in such a way that the center of the plate is 2.5 m below the free surface of water. a. Determine the area (in sq.meters) of the plate b. Determine the magnitude of the resultant force on the plate.
Blocks A and B weigh 30 lb and 50 lb, respectively. В M = 0.5 20° MBA = 0.6 C D MẠC = 0.4 If the weight of block D is to be greatest without causing motion, using the coefficients of static friction indicated, what is the frictional force (Ib) between block A and the floor C?