4 dia 16 R. 3. The grip strengthener shown in Fig. 1 is composed of a helical spring made of 4 mm diameter A227 hard-drawn Wire clip wire. The main coil has an outer diameter OD = 32 mm and a total number of body turns N, = 3.5. During operation, assume that the force applied to the handles Molded 112.5 plastic handle 87.5 occurs at a distance of 50 mm from the base of the handle. Using a design factor at closure of n,= S,lo,= 1.1, calculate the torsional spring constant k` and the force F,

4 dia 16 R. 3. The grip strengthener shown in Fig. 1 is composed of a helical spring made of 4 mm diameter A227 hard-drawn Wire clip wire. The main coil has an outer diameter OD = 32 mm and a total number of body turns N, = 3.5. During operation, assume that the force applied to the handles Molded 112.5 plastic handle 87.5 occurs at a distance of 50 mm from the base of the handle. Using a design factor at closure of n,= S,lo,= 1.1, calculate the torsional spring constant k` and the force F,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.
A Helical Compression Spring is made of A232 Chrome-vanadium with squared and ground ends has wire diameter 5 mm, outer diameter 81.5 mm, free length 246.3 mm and total 10 turns. Do the analysis if the spring is safe and if not, what is the largest free length to which it can be wound using ns=1.2? Attach File Browse My Computer
spring is to be inserted with an initial compression to produce a force equal to 125 N between the right-hand end of the lever and the stop. When the maximum force at A reaches to a value of 200 N, the end of the lever moves downward by 25 mm. assuming a spring index 8 determine the following parameters: 1. Spring rate 2. Size of the wire 3. Outside diameter of the spring 4. Number of active coils, and 5. Free length, assuming squared and ground ends Note: the allowable shear stress may be taken as 420 MPa, and G = 80 GPa. Hint: Ans. 0.33 N/mm: 3.4 mm; 27.2 mm; 77 mm - 200 mm - 200 mm Lever Stop -Spring
It is required to design a helical torsion spring and Cold-drawn steel wire of Groele 4. The yitld strength the ultimate tensile strength, and the factor of Safety is 2. from space Considerations, the spring Per a window-shade. The is made of patented of the material is 60l. mean Coil. diameter is kept as 18 mm. The maximum be- Inding moment asting on the spring is e5oN-mm. The modulng of elas ticity of the kNlmm?). The stiffness of the rad). Determine the wire diameter and the um Coils. Also, detesmine the deflectino and stored struin.energy. spring spring moterial is (207 should be(3 N-mm/ berof active
A helical compression spring is required for a mechanism under static loading with a maximum force of 1250N. The deflection caused by this load is 30mm the ends are squared and ground. The spring has an index of 6 and is made of cold drawn steel wire with tensile strength of 1090 N/mm and modulus of rigidity of 81370 N/mm2. The permissible shear strength is taken as 50% of the ultimate tensile strength. Design the spring and calculate: (a) The wire diameter (b) Mean coil diameter. (c) Number of active coils (d) Total number of coils (e) Free length of the spring (f) Pitch of the coil
A helical spring with a load range of from 450 N to 800 N from valve-closed to valve-open conditions is used to close the valve of a spring-set relief valve having a lift of 10 mm. Assuming the spring wire to be of chrome vanadium steel, the spring is rendering average service, determine the diameter of the wire if the spring index is 7 and Sg - 420 MPa. Use G=83GPA. Select one: O a. 2.4-mm wire O b. 5-mm wire O c. 6-mm wire O d. 7-mm wire
A helical compression spring is wound using 0.12-in-diameter phosphor-bronze B159 wire. The spring index C = 10 and the total number of coils is N = 14. You may assume that the spring has both ends squared and ground and is supported between fixed ends. Also, Sgy = 0.45 · Sut- a. Estimate the spring rate. b. Estimate the static load corresponding to the yield strength. c. What should the free length of the spring be to ensure that when it is compressed solid the torsional stress does not exceed the yield strength? d. Calculate the critical value of the free length of the spring to avoid buckling.
Problem 3: Design a helical compression spring to be used to return a pneumatic cylinder to its original position after being actuated. At a length of 10.50 in, the spring must exert a force of 60 lb. At a length of 4.00 in, it must exert a force of 250 Ib. Severe service is expected. Use ASTM A231 steel wire.
Problem 1. Select a proper key for the joint shown in figure bellow. Shaft has a diameter of 30 mm and transfers a constant torque of T= 180 N.m. The hub has length of Ia=50mm. The key is made from steel with Oall comp 3D 120 МPа оall sh 3D 100 MPа. %3| Table 2.1 Square key parameters Keyslot depth Keyway depth t1 1,8 2,5 3,0 3,5 3,5 3,5 4,0 5,0 Shaft diameter Key parameters 3 1,4 12 - 17 17 - 22 22 - 30 30 - 38 38 - 44 44 - 50 50 - 58 58 - 65 4 1,8 2,3 2,8 2,8 2,8 3,3 3,3 5 10 6 12 14 6 16 7 18 7 Lp Figure 1. Square key parameters. All dimensions are in millimeters.
An automatic door lock system is to be designed for automatically locking/unlocking car doors. The design will utilize an electric solenoid with sufficient force and stroke to provide the necessary motion. If the force required to drive the lock linkage is 9.5 N, determine if the solenoid with the following specifications meets this requirement: Number of turns Current Air gap Plunger dia, 2500 1.0 Amps 10 mm 18 mm The initial force available from a solenoid F P=2(ND)² HA 82
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures
A helical compression spring is required to provide a minimum force of 150 lb at installation and have a working deflection of 1 in. The spring rate is 75 lb/in. The coil must fit in a 2.1-in-dia hole with 0.1 in total clearance. Use 0.25-in diameter unpeened music wire and squared/ground ends. Use a 15% clash allowance, shear modulus G = 11.5 Mpsi, and weight density γ = 0.285 lb/in3. Assume Sys = 0.6Sut. Part A Find the shear stress at the initial deflection. Express your answer in pounds per square inch to three significant figures. τiτi = Part B Find the mean stress. Express your answer in pounds per square inch to three significant figures. Part C Find the alternating stress in the coil. Express your answer in pounds per square inch to three significant figures. Part D Find the fatigue safety factor for infinite life in shear. Express your answer using three significant figures.…