5. A pipe with an outside diameter of 2.5 inches is insulated with 2 inches layer of asbestos (k = 0.396 Btu- in/hr-ft²-°F), followed by a layer of cork 1.5 inches thick (k = 0.30 Btu-in/hr-ft²-°F). If the temperature at the inner surface of the pipe is 290°F and at the outer surface of the cork is 90°F, calculate the heat loss per 100 ft of insulated pipe. (Btu/hr)

5. A pipe with an outside diameter of 2.5 inches is insulated with 2 inches layer of asbestos (k = 0.396 Btu- in/hr-ft²-°F), followed by a layer of cork 1.5 inches thick (k = 0.30 Btu-in/hr-ft²-°F). If the temperature at the inner surface of the pipe is 290°F and at the outer surface of the cork is 90°F, calculate the heat loss per 100 ft of insulated pipe. (Btu/hr)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.26P

See similar textbooks

Similar questions

The interior-wall temperature of an annealing oven constructed of firebrick (Missouri) is2552°F, and the exterior-wall temperature is 392°F. If the heat loss is 3600 Btu/(hr)(sq ft),determine the thickness of the wall, in inches. (answer 5.67”)
2. A glass window has an area of 5.5 ft² and a thickness of 5 mm. If one side is at a temperature of 45° F and the other is at 23 F, how much thermal energy (BTU/year) flows through the window in one year? The thermal conductivity of glass is 1.89x10-4 kcal/m-s-K.
Find the thermal resistance r (in hr - °F/BTU) and the equivalent R-value (in hr ft?. °F/BTU) of a typical frame 20' x 7.5" wall consisting of a 0.5" plaster board on the inside of the room, nominai 2 x 4 studs, and a 0.5" sheathing on the outside. The spaces between the studs are filled with an R-15 insulating foam. What is the heat loss (in BTU) through this wall in four hours if the inside temperature is 72°F and the outside temperature is 32°F? (Assume that the 15% of the wall's area are studs and the remaining 85% is filled with the insulating foam. Assume that the air is moving outside the wall.) r= 0.0805 x hr: OF/BTU R=0.09 x hr ft2. F/BTU AQ = BTU
Two rods are horizontally fixed to the rigid walls so that there is a gap of 0.008 inch between them when the temperature is 60°F. The following are the properties of the rods: Property Rod 1 Rod 2 Diameter 1.25 inches 1.25 in Length 3.5 inches 7.5 inches Thermal Coefficient of 9.4 x10-6 /OF 13 x10-6 /°F Expansion Modulus of Elasticity 10 x 103 ksi 18 x 103 ksi a. What is the average stress in the rods if the temperature is increased to 240°F. b. What is the total deformation of the first rod?
What is the rate of heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? thermal conductivity of Celotex in AES = 0.028. Pls determine the temperature gradient and the direction of the heat transfer as well.
Question 1 Two walls of a storage plant composed of insulating materia (k=0.25 KJ/hr-m-°C) with 15 cm thick and concrete (k=3.2382 KJ/hr- m-°C) with 10 cm thick. The surface temperature on hot side is 35°C an sold side is-10°C. If the area is 8 sq. meter, find the temperature between walls. Note: Insulating materials on cold side. O-7.78 deg C 32.79 deg C 34.12 deg C 1 pts 28.34 deg C
Answer within 10 minutes : The temperature at the inside surface of an oven is 460 oF. The inside wall of the oven is made of brick and is 8 inch thick. The thermal conductivity of the brick is 2.2 Btu/hr.ft2.(oF/ft). The outside of the oven is covered with a 3-inch layer of asbestos as insulation, which has a thermal conductivity of 0.11 Btu/hr.ft2.(oF/ft). If the outer surface of the insulation has a temperature of 100 oF , calculate the amount of heat lost through 2 ft2 of wall area in 3 hours.
a metal bar is made up of 3.0 cm of aluminum and 5.0 cm of steel. the free end of the aluminum bar is placed in contact with steam at 100 degree Celsius. at the other side, the free end of the steel bar maintained at 0 degree Celsius by placing it in contact with the ice. find the temperature at the point that connect the aluminum and the steal (junction)
Saved Help Save & Exit A 2-kW resistance heater wire with thermal conductivity of k= 70 W/m-K, a diameter of D= 4 mm, and a length of L = 0.9 m is used to boil water. If the outer surface temperature of the resistance wire is Ts= 230°C, determine the temperature at the center of the wire. (Round your answer to a single decimal place.) 230 C -D→ es Resistance heater The temperature at the center of the wire is °C 18°C Clear ^ 4 ENG
A water tank is completely filled with liquid water at 40°C. The tank material is such that it can withstand tension caused by a volume expansion of 5 percent. Determine the maximum temperature rise allowed without jeopardizing safety. Assume a volume expansion coefficient value at that of 65 °C. (Just write the numerical answer. Include - if the answer is negative. No need to put the unit.) Properties of saturated water Volume Specific Heat Jkg - K Thermal Conductivity k, Wim- K Prandti Enthalpy Dynamic Viscosity H. kg/m -s Expansion Coefficient Number Density P. kgim Saturation of Pr Temp. T, "C B. 1/K Liquid Pressure Vaporization P, kPa Liquid Vapor hg, k/kg Liquid Vapor Liquid Vapor Liquid Vapor Liquid Vapor 0.0171 1.792 x 103 0.0173 0.922 x 105 13.5 0.934 x 10-5 1.00 -0.068 x 10 3 1.00 1.00 0.01 0.6113 999.8 0.8721 0.0048 0.0068 2501 2490 2478 4217 4205 1854 0.561 0.571 1.519 x 10-3 1.307 x 10-3 0.946 x 10-5 1.138 x 10 3 0.959 x 10-5 1.002 x 10 3 0.973 x 105 999.9 1857 11.2 0.015…
A box made of copper plate with outside dimensions of 5 ft by 5 ft by 6-in.is suspended horizontally in a large room where the air and wall temperaturesare 80°F. The box contains a heating coil which maintains a temperature of500 °F on all external surfaces. What is the total heat loss from the box inBtu/hr.
The 12ft x 14 foot room illustration in figure 1.6a has an exterior wall at a surface temperature of 60°F, a window surface temperature of 40°F (double glazing on a cold day). The two interior wall surfaces are a temperature of 72°F. Determine the MRT sensation of a person standing in the center of the room. (See figure 1.6 below) Round your values to the nearsest hundreth decimal place (0.00). You will need to upload your mathematical work in question 4.