A 460-V, 25-hp, 60-Hz, four pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: R, = 0.641N R2 = 0.332N X1 = 1.106N The total rotational losses are 1100 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.2 % at the rated voltage and rated frequency, find the motor's a) Speed X2 = 0.4640 Хм — 26.30 d) Pcony and Pout b) Stator current e) Tind and Tioad c) Power factor f) Efficiency

A 460-V, 25-hp, 60-Hz, four pole, Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: R, = 0.641N R2 = 0.332N X1 = 1.106N The total rotational losses are 1100 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 2.2 % at the rated voltage and rated frequency, find the motor's a) Speed X2 = 0.4640 Хм — 26.30 d) Pcony and Pout b) Stator current e) Tind and Tioad c) Power factor f) Efficiency

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss the effects of rotor resistance in T-S characteristics of 3 phase induction motor.
Choose True (V) or false( x) for the following : 4) Reluctance is a measure of "opposition" the magnetic circuit offers to the flux. 5) The rated output power (transformer rating) can be used to determine the turns ratio of the transformer. 6) With the increase in speed of a series DC motor, Both back emf as well as line current increase. 7) When an induction motor is stationary, the stator and rotor windings form the equivalent of a transformer. 8) Increasing the load current for DC Self-excited generator Shunt-Wound Generator will increase the terminal voltage. 9) In lap windings there are as many paths in parallel and used to produce high current, low voltage output. 10) In 3-pahse induction motor, if the rotor speed increases, the rate at which the rotating magnetic field cuts the rotor bars is increasing.
In alternator armature winding why we prefer : a- short pitch winding w.r.t. full pitch winding? b- distributed winding w.r.t. concentrated winding? c- double layer winding w.r.t. single layer winding?
The amount of torque developed by a 3-phase squirrel-cage induction motor from no-load to rated-load is proportional to the amount of current flow through the rotor conductors. a) directly b) inversely If n
What are the various losses in an induction motor? On what factors do they depend? IV. V. List the different types of stray load losses in an induction motor.
V. List the different types of stray load losses in an induction motor.
Write a summary ( point) about equivalent cricuit of three phase induction motor .
Q4) a)discuss the equivalent circuit and slip in a single-phase motor. b)discuss the core - losses (Rc).
A three-phase induction motor operates at a slip of 3% and has a rotor copper loss of 300W. The rotational loss is 1500W. Determine (a) the airgap power and (b) the power output.
A short shunt compound DC generator supplies a load current of 10A at a voltage of 10 volts. If the resistance of armature, shunt field and series field windings are 0.001 ohm, 1 ohm 0.00 ohm respectively. a) Draw the the figure. And find the generated voltage.
An 3-phase induction motor(IM) has full load slip = 0.5%. If the rotor circuit resistance is increased so that R2new =2R2old, then the slip at which the motor develops the same full load torque is=.. * ......
A 4 pole, lap wound d.c. generators has 42 coils with & turns per coils.It is driven at 1120 r.p.m. If useful flux per pole is 21 mWb, calculate the generated e.m.f. Find the speed at which it is to be driven to generate the same e.m.f.as calculated above, with wave wound armature.