A 63.5 mm shaft having a yield point of 50 ksi with a ¾ inch width key. Compute the length of key in order to transmit the torque on the shaft. The shearing stress of key is 22 ksi and use factor of safety of 2. (Ans: 3.72 in)

Q: The force applied at the handle of the rigid lever causes lever to rotate 0.04 radians clockwise…

A: Find the stress in each cable and force applied at point E.

Q: Calculate the convective heat transfer rate from a 40-cm diameter horizontal pipe whose surface is…

A: Given data as per the question Diameter of pipe =40 cm Surg=face temperature of pipe =950 c The…

Q: Q1/Water enters a boiler at (323°K & 5 Mpa), and leaves as steam at (673°K & 5 Mpa). The heat…

A:

Q: The air at the inlet to the compressor currently has an average temperature of 24°C and the…

A:

Q: 3) The unit of force in S.I. system of units is dyne O kilogram O Newton watt

A: We are supposed to answer the SI unit of force. Let us understand each of the given units: (1) Dyne…

Q: What is the kinetic energy of a 3000 lb. automobile which is moving at 33 fps?

A:

Q: The figure shows a PV diagram similar to the cycle of a Diesel engine. It consists of two adiabatic…

A: Given: The given cycle is similar to diesel cycle and heat input and exhaust heat is represented as:…

Q: The tangential acceleration of the centrifuge is given by    a  =  0.5 t    m/s/s    where  t  is in…

A:

Q: At what rpm should the lathe revolve to rough turn a piece of cast iron (CS = 60 SFPM) 51 mm in…

A: Question: At what rpm should the lathe revolve to rough turn a piece of cast iron

Q: Determine the N.F. of the D.O.F. Springs - Mass Systems as shown in Figures below? k M1 wwwwwwwwww…

A: given; find degree of freedom(DOF)=?

Q: A centrifugal pump is used to supply a highly viscous fluid to a chemical plant. The chemical plant…

A: Given data Chemical Plant is located at a height of 20 m above the pumping level.The flow rate in…

Q: Give 5 examples of jobs where sealant and adhesive can be applied or used.

A: 5 examples of jobs where sealant and adhesive can be applied or used

Q: What is name of the system below, Explain its function, where it is used, what is the neasuring…

A: The force that a fluid (liquid or gas) would exert while at rest on a unit area, such as pounds…

Q: Problem 2. Use the method of superposition to find the slope at B. You do not have to draw a shear…

A:

Q: Consider a 2-dimensional incompressible flow field. The vertical component of velocity for the flow…

A: We can answer up to 3 subparts so we will answer first 3. Please resubmit the question by specifying…

Q: Determine the shear and moment as functions of x if x is greater than 4ft but less than 6ft.

A:

Q: 1. 1 2. 0 3. 12 4. 15 If two vectors a = 3i+4j7k and b = pi - 6j + 3k are perpendicular, the value…

A: Given, Vector a → = 3 i + 4 j - 7 k Vector b →= p i - 6 j + 3 k   When two vectors are…

Q: 6. A shaft revolving at 1740 rpm is supported by bearing with a length of 150 mm and diameter of 64…

A: GivenN=1740rpmL=150mmd=64mmμ=2.4×10-0 reyns=16547.4 Pa st=0.136mm

Q: The wrench is applied to two forces each of magnitude P. The steel shaft AB has a diameter of 15 mm.…

A:

Q: Electrical Engineering 12 ksi 8 ksi + For the given plane state of stress, determine: a) the main…

A: Find the main plans and main stresses.

Q: Find the forces in the members AE, DE, and AC of the truss shown Assign a tension or compression…

A:

Q: The concept of variable banking for racetrack turns is shown in the figure. If the two radii of…

A:

Q: A high strength drill rod used for boring a hole in the earth has a diameter of 50 mm. The allowable…

A:

Q: 3. Steam at 140 bar and 400°C enters the high pressure turbine and expands to 3 bar. 5 400 kg/hr of…

A:

Q: consider a system that involves a lower critical solution temperature, the components are more…

A: Introduction: lower critical solution temperature is that temperature above which the component is…

Q: calculate the accelerations that are requested using the graphical method B D AB-5.5cm AC-88cm…

A: Given : To find : ad,ab,α5

Q: An oil of kinematic viscosity of 0.5 stokes flows through a pipe of 20 cm diameter. What is the…

A: From the data given in question, Kinematic viscosity = v = 0.5 stokes = 0.5 x 10-4 m2/s Diameter of…

Q: There are compressed 11.33 m3/min of air from 103.42 kPa, 26.7°C to 827.36 kPa. All clearances are…

A:

Q: The process capability index C, is

A: Given; Determine process capability index Cp ?Where, Statistical quality control tests show a mean…

Q: 22 kg of CO₂ at 300 K is kept in a vessel of 5m capacity. Find the pressure exerted by CO₂ in the…

A: Given that, m=22 kg, T=300 K, V=5 m3 Gas is CO2 its molecular mass M=44 kg/kgmoles…

Q: the combined one-dimensional heat conduction equation. Show step-by-step solution and schematic

A:

Q: What are the recommendations for Boeing to be successful in the future? Please provide examples of…

A: Given Boeing To find Recommendation

Q: 2. A closed rigid vessel contains 25% liquid water and 75% water vapor by volume. The liquid-vapor…

A: Given that : volume of liquid = Vf = 0.25V volume of vapour = Vg = 0.75V  temperature = 150 degree

Q: 4. A string has a diameter of 1 cm and the original length of 2 m. The string is pulled by a force…

A:

Q: charges at point the radius of CL

A: solution of above problem is below:

Q: 1. At time t=0, the velocity of cylinder A is 0.3 m/s down. By the methods of this article,…

A: Tension is a pulling force acting in one dimension along the cables' axis in the opposite direction…

Q: We make a composite with an Al matrix (E = 70 GPa) and SiC particles (E,= 430 GPa). We add enough…

A:

Q: A large flat plate is subjected to constant-amplitude uniaxial cyclic tensile and compressive…

A: Given Dataa=1mmKk=35MPa m1/2m=3.5A=5×10-12 MPaY=1.3σmax=120MPaσmin=35MPa

Q: A 4-cm-diameter aluminum cylinder and a 2-cm-diameter steel cylinder are positioned snugly between…

A:

Q: Determine the cross sectional

A: Given; In an arc welding process welding speed is doubled. Assuming all other process parameters to…

Q: Calculate the horizontal distance a in Figure Q3b. Calculate the reaction forces RA and Rc that…

A: According to details provide in the question we need to calculate  (i) value of the a (ii)reactions…

Q: Centroid at area along x axis. Centroid at area along y axis.

A:

Q: 1. The five forces shown in Figure 1-59 are in equilibrium. Compute the values of P and F. 20 KN 60°…

A: Given

Q: Consider the spherical enclosure in Figure QA6. Assuming that the surfaces A₁ and A₂ are diffuse,…

A: The following expression is derived using basic definition of view factor.

Q: By adding a condenser to the steam plant in problem#1, the turbine back pressure was reduced to 0.2…

A:

Q: Problem 1. Use the differential equation method (either second, third or fourth order) to find a)…

A: given; lets take reaction force at A=RAlets take reaction force at B=RB

Q: 2: For the beam shown in Fig.(2), find the reaction forces at supports A and B respectively? %) 20…

A:

Q: The coefficient of Performance (COP)

A: Given; It delivers the heat to a room that must be kept warm at; T= 300 KWhere heat pump absorbs 10…

Q: Each of the four links in Figure  has an 8x36mm uniform rectangular cross section and each of the…

A: Consider the free body diagram as shown below for the link ABC. From the moment equilibrium about…

Q: propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable…

A:

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.