A beam is created by nailing 3 planks together with 2 rows of nails as shown above. The beam exhibits a pin support at A and is suspended by a cable at B. A concentrated load of 10 kN is applied at the free end while a moment of 25 kNm is applied at location B. a) Determine the second moment of area (I) of the cross-section b) Draw the free body diagram, shear force diagram, and bending moment diagram of the beam c) For the maximum shear force on your SFD, determine the maximum and minimum shear stresses at the interface between the horizontal and vertical planks d) For the maximum shear force on your SFD, Determine the shear stress at the neutral axis

A beam is created by nailing 3 planks together with 2 rows of nails as shown above. The beam exhibits a pin support at A and is suspended by a cable at B. A concentrated load of 10 kN is applied at the free end while a moment of 25 kNm is applied at location B. a) Determine the second moment of area (I) of the cross-section b) Draw the free body diagram, shear force diagram, and bending moment diagram of the beam c) For the maximum shear force on your SFD, determine the maximum and minimum shear stresses at the interface between the horizontal and vertical planks d) For the maximum shear force on your SFD, Determine the shear stress at the neutral axis

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E0=205GP,, Ga=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x10-mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vAD 2. The normal strain in member AD, caD 3. The average stress experienced by pin A, T, 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
A В C 12 kN For the frame and loading shown, determine the components of the forces acting on member DABC at B and D. 0.5 m D E F 6 kN 0.5 m H 0.6 m 0.4 m 0.2 m
A built-up section is made from 450mm x 20mm as flanges and 500mm x 20mm as web as shown. All plates are A50 steel and the flanges are continuously connected to the web by means of weld. This section will be used as a beam to support a factored distributed load as shown. 450mm x 20mm 50 KN/m 5.0m 3.0m 450mm x 20mm A. Determine the moment of inertia along the neutral axis. B. Determine the shear flow at the neutral axis. C. Determine the shear strength capacity and adequacy of the built-up section using LRFD-NSCP 2015 provisions. 500mm x20mm
1) The wavren truss loaded as shown is supported by a voller at C. Use the method of sections to compute the Force in bars hinge at G and by Вс, аnd CE. 800lb Goolb B F 20" A 20 20 20" 400lb 1000lb
The frame shown below is subjected to an applied Point Load of 27kN and a Uniformly Distributed Load of 3kN/m and is supported at A by a pinned connection and at B by a roller connection. Calculate the vertical support reaction at B. Give your answer in kN to 2dp. 3m 3m PL UDL 5m A
Determine the magnitude of the pin force at A. Assume W - 620 Ib, a- 4.6 ft, b-3.1 ft,r-8 in. C B W Answer: A- Ib
The cantilevered W530 x 150 beam shown is subjected to a 7.5-kN force F applied by means of a welded plate at A. Determine the equivalent force-couple system at the centroid of the beam cross-section at the cantilever O. 0.58 m -5.3 m- 28 Answers: F = i+ i j) kN Mo = k kN-m
250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars (E=205GPA, G,A=82GPA) and is pinned to plate ABC using a 5 mm diameter pins as shown in the figure. The yield strength of the pins is T,=890MPA. Plate ABC is a right triangle and is fixed along its edge BC. A 25KN Force P is then applied at end D causing a lateral strain in member AD with magnitude equal to 7.5x104mm/mm. This also causes Point A to displace only along the horizontal resulting to a shear strain at point A equal to y,=+0.00165rad. Determine the following: 1. Poisson's ratio of material used in member AD, vD 2. The normal strain in member AD, CAD 3. The average stress experienced by pin A, TA 4. Factor of Safety of pin A with respect to yielding, FS,A 5. Displacement of point D, A,
/stemezcom Lec3 working stres For the beam shown below, determine the concrete and steel stresses at the locations of the maximum positive and negative moments, Use ſ'c = 25Mpa. The answers are MPa, MPa, MPa and MPa. 3okN/m 8m 1m 4-25mmØ- -Top bars -4-16mmØ 250 250 bottom bars 630 630
A 72 2 (a) 8 W+ W 2 (c) 2 2W+ с W) 2 T 72 30⁰ A beam AB of length 1 and weight w supports a load W at its free end B and is hinged at its end A. A wire CD supports the beam at the mid point C making an angle of 30° with the horizontal. What is the value of tension T in the wire CD? D B W (b) 4 (2W + w) (d) 4 W+ W 2
The bridge truss shown carries the following uniform live load and concentrated live load. в с D A B E 3m K F G H J SO8m W(LL) P(LL) 15 110 Calculate the following: 7. Maximum force on member GH
Calculate the maximum tensile and compressive stresses in the section of BC of the beam. 75 mm 75 mm Empedopre|72 -75 mm 150 mm 50 mm EN SAMA 00 kN B 1.0 m 60 kN -1.5 m-> rode D 1.0 m