A cylindrical core having a radius 2.54 102 [m] and length of 0.3 [m], was flooded with brine at a steady rate of 1.100 [m³s¹], the differential pressure across the core was 10 [bar]. Calculate the absolute permeability of the core. Assume brine viscosity 0.001 [Pa.s].

A cylindrical core having a radius 2.54 102 [m] and length of 0.3 [m], was flooded with brine at a steady rate of 1.100 [m³s¹], the differential pressure across the core was 10 [bar]. Calculate the absolute permeability of the core. Assume brine viscosity 0.001 [Pa.s].

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air A Water Calculate the gauge pressure, in kPa, at A, B, C, D in the reservoirs shown above. (Note that the reservoirs between A and B are connected.) Problem parameters: h1 = 1.1 [m] h2 = 0.3 [m] h3 = 0.4 [m] h4 = 0.5 [m] Density of water is 1000 [kg/m³]; Density of air is 1.225 [kg/m³]; g = 9.81 [m/s²] S.G. of oil is 0.89 h4 [m] h3 [m] h2 [m] Air B h1 [m] Oil
(c) Figure 1 shows a tube in a water container. Given the below conditions; Pressure when water begins to evaporate = 2kPa Inner tube wall contact angle = 6° • Surface tension = 1.00 N/m Calculate h [m] and the diameter of the tube [µm] for the highest capillary rise scenario. Water Figure 1
2 Eg = 200 GP₁ A₁ = 200 mm ² T point A and point D lies 2.625 m Find the reactionary force A 1.45 [m] C A₂ = 400 mm² Point Cles from wall at B. ат в in A₁ 19.0 [kN] 4₂ E . 5.250 [m] 0.725 m x-direction. (UNIT KN) De from pin at 65.0 [kN] B
A Venturi Tube develops low pressure on its throat, which can suck water from a deposit located under it. Assuming permanent flux with no losses, calculate the V1 necessaryto suck water from the deposit to the throat. D1 = 15 [mm]; D2 = 37 [mm]; h = 163 [mm]; pa = 101325 [Pa] (atmospheric pressure). Express the solution in [m/s]
A gas flows of from a station (a) with pressure of 20[bar] through a pipe with 0.4[m] diameter and4000 [m] length to a different station (b). The pressure at the exit (station (b)) is 2[bar]. The gasand the sounding temperature can be assumed to be 300 K. Assume that the flow is isothermal,k=1.4, and the average friction f=0.01. Calculate the Mach number at the entrance to pipe and theflow rate.
1. A full gas cylinder contains nitrogen gas at 70° F and the maximum allowed pressure [2640 lb/in.2 (gauge)]. If it were left in the sun and the contents reached a temperature of 210° F, what is the resulting pressure in the cylinder?
When crude oil with a specific gravity of 0.80 and a viscosity of 27 [p] is transported at 200 [m^3/h] using a 10" standard steel pipe, find the two losses (head loss) and pressure drop per 1 [km] of pipe length.
1. Initial temperature in the entire system is 20 °C. If the system is heated up to at which temperature to copper and aluminum rods do not exceed safety limits? 0.2 mm d Cu 400 mm AI D 300 mm Al :D=50 mm E=70 GPa a=23.10 [1/°C] Gallowable 50 MPa Cu: d=40 mm E=100 GPa a-27.10 [1/C] Gallowable 100 MPa
2. Find the depth of a point below water surface in sea where the pressure intensity is 100.55 kN/m². Specific gravity of sea water is 1.025. [Ans. 10 m]
A cylindrical pipe with a cross-sectional radius r = 1.40[cm] is plunged into a l = 2.30[m] tall open water drum that is initially completely filled with water (pwater = 1000 [kg/m3]). The pipe goes h1 = 0.35 [m] above the drum before dropping down h2 = 3.50 [m] below the base of the drum as shown. The cross-sectional radius of the top side of the pipe is R = 2.20 [cm].A. How fast is the water going out of this pipe?B. What's the liquid's pressure at the top of the pipe? Assume that the system is exposed to 1.00 [atm] of air pressure.C. What's the maximum height the pipe can go above the drum before the water stops flowing out of the pipe? For liquid flow to be continuous, the liquid’s pressure must not fall before its vapor pressure. Assume that vapor pressure, in this case, is 2.30 [kPa].
12. Imagine a solar collector for hot tap water in a hot climate. De outdoor temperature is 22 degree Celsius. De tank of the solar collector is placed outside, and the cold water temperature to the collector is 20 degree Celsius. De water flow rate through the collector is 45 liter/hour. De collector is 2 [m2] and the average solar radiation in the time period considered is 1000 [W/m2]. What is the temperature of the hot water to the tank? The efficiency of the collector can be assumed to be 0.7 (we neglect the dependency to the water temperature) (multiple choice, one answer) 34 [OC] 47 [OC] 54 [OC] 67 [OC] 74 [OC]
Prob2 Consider water transfer between two larger storage tanks. Lower tank water surface 10 m lower than water surface of the elevated tank. If Q=1.0 m³/s find total losses, h₁=? [m] and [KW]=?