A device shown has a solid circular cross section, 35mm in diameter; it has a length of 1200 mm.and made from SAE 4150 OQT 1300, with a circular cross section and pinned ends. what would be the allowable loading on the column if N = 3.75. and what is the resulting force F knowing that 0 = 23°

A device shown has a solid circular cross section, 35mm in diameter; it has a length of 1200 mm.and made from SAE 4150 OQT 1300, with a circular cross section and pinned ends. what would be the allowable loading on the column if N = 3.75. and what is the resulting force F knowing that 0 = 23°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: c kN b kN/m B E “a" m 4 m 3 m 3 m

Q: A RC column of square cross-section (400 x 400 mm²) has its column load-moment interaction diagram…

A: Given- RC column-400×400 mm2Pu=640 kNfck=20 MPaIt is needed to find maximum uniaxial eccentricity…

Q: The pulley system below is in static equilibrium, where load W3 is 730 N, angle a = 50° and angle 0…

Q: A steel column with effective length of 8 m (supported with fixed at both ends) is supported with…

Q: A RC column of square cross-section (450 mm x 450 mm) has its column load-moment interaction diagram…

A: Given data,Width of column =450 mmDepth of column =450 mmThe maximum eccentricity at which a…

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1690…

Q: Solve the angle of twist on a solid shaft, with 5cm radius and 50cm length, if the torque applied is…

Q: a lb/ft b lb/ft А В d ft c ft-

Q: Example 4.5 4.8 m. The member is to be used in a transmission line tower and is as shown ends are…

Q: The tank shown with elliptical cross-section is fabricated from 11.7 mm steel plate. Determine the…

Q: Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is…

A: There can't be any reaction at D. There is no vertical element at D Reaction at E, RE = 940lb At…

Q: Using the Area Moment Method. What is the reaction components of the beam? Whereas, E=200GPa…

A: The effect of a fixed support may be replicated by adding an imaginary span to the right side of the…

Q: The dresser has a weight of 60 lb and is pushed along the floor as shown in. Assume h = 4 ft. The…

Q: 1. If P = 1800 Ib, determine the following a. force F in lb 10olb P. F 20olb b. Horizontal reaction…

Q: A 8.7 m long beam is loaded as shown below and the hinge support is at x=2.5 distance from the left…

A: Calculate the net load acting on the beam. It acts at the centroid of the loading. Now using…

Q: The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and…

A: Finding out twist developed in steel from support B.

Q: A steel beam cantilever beam [Est = 27000 ksi; I = 950 in."] is loaded by a distributed load of w =…

A: A cantilever beam is a direct member of a building or structure. It can be used to transfer the load…

Q: 2) How large are the reaction forces and bar forces in the given jib? Given: F1 = 20 kN, F2 = 10 kN,…

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

Q: In the figure, the loading condition and cross-section are given to the 4m-long AB column with a…

Q: The hand cart has wheels with a diameter of 80 mm.If a crate having a mass of 500 kg is placed on…

A: The above question refers to friction acting on the body and the plane. The coefficient of friction…

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1530…

Q: B C D D00 -L/2 -L/2- -L/2

A: Using free body ABCD with distributed loads replaced by equivalent concentrated load: Mc=0…

Q: CHAPTER 4: *FROM ....TL 2014 The load is 80 kN supported by the four 304 stess steel wires that are…

A: To find vertical displacement of the load

Q: A hollow steel shaft, 5.8 ft long, has an outer diameter of 3.06 in. and an inner diameter of 1.28…

A: Given data: Length of shaft=5.8 ft Outer dia=3.06 in Inner dia=1.28 in Power==203 hp N=133 rev/min…

Q: A В |+ c a

Q: (a) At what distancex from the free end does the maximum bending stress omax occur? Round your…

Q: MA = 1e kg and MB = 20 kg are connected by a rigid bar of negligible mass. Find the acceleration of…

Q: The crankshaft is subjected to a torque of M = 50 N ⋅ m. Determine the horizontal compressive force…

A: The given figure is shown below:

Q: For the beam loaded as shown in the figure below, determine the following unknowns using any method…

Q: An inclined rectangular gate with water on one side is shown in the figure. The gate has dimensions…

Q: Equilibrium of Rigid Bodies Additional Practice Problem 1. Given the diagram below, find the tension…

Q: A determinate frame carries a concentrated and distributed load as shown in the figure. Determine…

Q: An inclined rectangular gate with water on one side is shown in the figure. The gate has dimensions…

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I= 1730…

Q: The shear diagram for beam is shown in the figure. Assuming that no couples ac as loads on the beam,…

A: The shear force diagram represents the loads and their type whether the load is concentrated,…

Q: A homogeneous steel shaft (G=83GPA) is loaded as shown in the above Figure. Assuming T = 300 N-m,…

Q: • Problem 14.1. Determine elastic curve of the solid circular shaft. The shaft is made of steel…

Q: F B A d The wagon has a mass of 19.5 kg and centre of mass at G. Both the front and rear wheels are…

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; / = 1950…

Q: Q6 -Determine the maximum force P that can be applied without causing movement of the 90-kg crate…

A: Determine the maximum force P that can be applied without causing movement

Q: 26, A weight of 500N is supported by two mętallic ropes as shown in the figure. The values of…

Q: A 5m cantilever beam is shown in the figure below. A uniform dead load and live load is given on the…

A: Concrete strength(fc)=27 Mpa, Yield strength(fy)=345 Mpa, Width of the beam(b)=300 mm, Depth of the…

Q: A circular steel shaft with length, L (m) has an outer diameter, d2 (mm) and inner diameter, d1…

Q: : For the column shown in Fig.5. Determine the maximum load P it can carry without buckling. lote…

A: Given data F.o.S = 2 Es = 200 GPa σy = 180 MPa L =3m we have to calculate max. load P it can carry…

Q: the beam and loading shown, determine the reaction (N) at the pin if 18068 N/m, V = 63739 N/m, x =…

A: To find reaction at pin support A

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1620…

Q: 2) How large are the reaction forces and bar forces in the given jib? Given: F1 = 20 kN, F2 = 10 kN,…

Q: solid shaft made of steel [G = 80 GPa] is subjected to the torques shown. Determine the angle of…

Q: The simply supported beam AB shown in the diagram has a length L-8 m and subjected to a uniformly…

A: To determine the bending moment under the load P. Given, Length of beam (L) = 8 m Unifromly…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

A device shown has a solid circular cross
section, 35mm in diameter; it has a
length of 1200 mm. and made from SAE
4150 OQT 1300, with a circular cross
section and pinned ends. what would
be the allowable loading on the column
if N = 3.75. and what is the resulting
force F knowing that 0 = 23°
L mm
L mm
Tink
link
F N.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Data Given

VIEW

Step 3 Calculation of allowable loading on the column

VIEW

Step 4 Conclusion

VIEW

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
f. Calculate the maximum safe load "P" in KN Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
Three cylindrical rods are welded together as shown in the f igure. The diameter and modulus of elasticity of the materials are given. If Q= 30kN; Evaluate the necessary P force make the def lection on B zero? b. Based on the calculate P force in (a) calculate the def lection on C? а. 300uL 125u 125. 300um d = 12mm E - 20Gpa d%3 8mm E = 20Gpa E= 20Gpa Q -P C A В
Hw: Find the Sslope and defletion in the section CA-A) and the section cB-B) fur the beam Showwn. Given, I = 5*l-"m4 aued Es 205 G Pa. A 2 kulm Im 2.5 m Im A
For the beam below, determine the following, assume EI is constant. What is FEMAB in k-ft? -18 --96 Select the correct response: -69 2 k/ft 18 24ft
8. H / The beam shown below has across seclion of channel Shape with width 360mm.and haghs h= loomm, the web thickness ist= 14mm.Deler- Mine ihe Max imum tensile aud Compressive stressin the beam due to unifom Load? 360Mm 3.6KN/M 14m tiom Please Sir 5T CASIC f-991ES PL DATURAL u CALC (-)
Q4\ Which of the following is a zero-force member? 3 8KN 4 G 4 エ子c D. 4 B AC BD IF ID
DETERMINE THE THE IS MAXIMUM SAFE SERVICE LIVE LOAD THAT THE BEAM CAN CAN CARRY IF SERVICE DEAD L O A D THE BEAM WEIGHT OF THE BEAM SECTION fy = 415 MPa. TOP BARS BOTTOM BARS ARE CENTER DISTANCE 12 KM/M INCLUDING AND BASED ON THE CAPACITY SHOWN. fc : 40 MPa AND ARE 6-32 mm. AND ARE - 3 - 28 mm. CENTER TO 3 BETWEEN THE USE 2015 NSCP Is 108 mm 00 0 0 300 G ט1 108 352 70. A (1 7.2m B TOP BAR LAYERS ↓ 6.7M C OM
Determine whether the column shown in Figure is adequate to support 850 kN dead load 2400 kN live load. The steel material is $275. The column is HE450B. P min 4500 mm T 4500 mm Homework 4 - Compression Members - Flexural Buckling Strength QUESTION 7 According to the calculation above, we can say that the flange and web elements are slender elements nonslender elements QUESTION 8 Calculate the buckling length according to the x axis (Lcx) (unit will be mm and no need to write the unit). QUESTION 9 Calculate the buckling length according to the y axis (Lcy) (unit will be mm and no need to write the unit). П
QI/ A beam carries the loads shown in figure, if the tensile stress must not exceed 20 MPa and the compression stress 70MPa. Find the maximum value of load P Som, r W=2-5p W/m - P Lﬂj Ko ; - 3,‘, ) o Jo 1 er -1 /i e,
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
The AD beam, which is fixed at left end, is under various loads as shown below. a) Draw internal load diagrams (Nx, Vy, M2) using the method of section. b) Determine the state of stress at points G, H and I for section B. c) For the corresponding points, indicate the results (i.e. stress components) on a differential element. b2 A B G М F2 2l h bi GIVEN DATA: Fo = 10000 N, F1 1200 N, F2 = 1000 N, qo = 50 N/cm, Mo = 50000 Nem, l = 25 cm bi = 10 cm, b2 = 20 cm, h 12 cm, t 1 cm