a) Find the value of K that yields max 20% overshoot... b) Peak time.. c) Setting time........ d) Fine the steady state and peak values...... e) Find the value of K that yields max 30% overshoot... f) Peak time. g) Settling time...... h) Find the steady state and peak values.... i) Determine the value of gain K to get the fastest response without oscillation. g) Settling time for the new gain....... T(s) = G(s) 1+G(s)H(s) 1+ s²+5+2 K s²+5+2 (1-²)

a) Find the value of K that yields max 20% overshoot... b) Peak time.. c) Setting time........ d) Fine the steady state and peak values...... e) Find the value of K that yields max 30% overshoot... f) Peak time. g) Settling time...... h) Find the steady state and peak values.... i) Determine the value of gain K to get the fastest response without oscillation. g) Settling time for the new gain....... T(s) = G(s) 1+G(s)H(s) 1+ s²+5+2 K s²+5+2 (1-²)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the nominal pi model which among these are divided into two halves? a. Series impedance O b. None of these. c. Shunt capacitance d. Both (A) and (B)
Q.1: For the single - phase, full-wave, uncontrolled rectifier, the supply voltage it 220V, 50HZ .the load resistor is 252. Calculate: (a) The average value of the output voltage and current. (b) The rms value of the output voltage and current. (c) The de power consumed by the load (Pdc) and the average value of the power delivered to the load (Pac).Sketch the appropriate voltage and current waveforms.
A single-phase full-wave rectifier, energized from a 220 Vrms, 50 Hz ac source, supplies power to an unknown load. The load current is shown in the figure together with the line voltage. a) Recommend a circuit for the load by examining the current waveform. Draw your circuit in PSIM and obtain same voltage and current waveforms. b) Calculate apparent power, the active power and power factor. Then verify the results using PSIM. A DA LOAD ? 本D。本D Vs[V] Is[A] Vs Is 5A 12ms 18ms t |s] 2ms 8ms -5A
Read the question carefully and match the answer with its respective question: The diversity factor on a power station is, 1.35. It is predicted that, next year the sum of individual maximum demand will decrease by 10%. But the maximum demand on the power station will increase by 12%. In comparison to the old maximum demand what will be the new one. Choose... What will be the new diversity factor? Choose...
In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.49 V respectively. The form factor of this circuit is ___________________. a. 1.63 b. 3.27 c. 0.61 d. 1.17
D) What are the methods for treatment steady state stability limit? Explain them.
An ideal single-phase source, 240 V, 50 Hz, supplies power to a load resistor R= 100 Ohm by full -wave rectifier (a) Calculate the average and rms values of the current and the power dissipation. (b) Calculate the circuit power factor and the ripple factor.
(b) A three-phase uncontrolled bridge rectifier is connected to an AC supply of 415V through a delta-star transformer as shown in the Figure. The load consists of large inductance to render a level load current of 60A at 300V. Assuming voltage drop across the power device to be 0.7V, compute the following: i) Rms value of secondary phase voltage and current; ii) Rms value of primary phase voltage and current3; iii) Transformer power rating in kVA and transformation ratio; iv) Device ratings. 本の。本の本の Load 本の。本。本の。 Figure
8.* A single phase bridge rectifier supplies a IkW washing machine induction motor drive. The smoothing capacitance is 6.8 mF and the smoothing inductance is 5 mH. At full load, the equivalent resistance of the induction motor is 24 2. The ac supply is 220 V (60Hz). (a) (b) (c) Estimate the ripple What is the capacitor 'de link' voltage under full load? What is the % voltage regulation no load to full load? ?
The diversity factor on a power station is, 1.35. It is predicted that, next year the sum of individual maximum demand will decrease by 10%. But the maximum demand on the power station will increase by 12%. In comparison to the old maximum demand what will be the new one. Choose... What will be the new diversity factor? Choose...
........ measures the dispersion around the expected value.
A resistor Ra is in series with a voltage source Va. Draw the circuit. Label the voltage across the combination as v and the current as i. Draw and label the volt–ampere characteristic (i versus v).