A Pipe carrying oil of specific gravity 0.92 changes in size from 250 mm at section 1 and 550 mm at section 2. Section 1 is 4.2 m below section 3 and the pressures are 90 kPa and 60 kPa respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow. provide complete solution asap

A Pipe carrying oil of specific gravity 0.92 changes in size from 250 mm at section 1 and 550 mm at section 2. Section 1 is 4.2 m below section 3 and the pressures are 90 kPa and 60 kPa respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow. provide complete solution asap

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 42P

See similar textbooks

Similar questions

1.56 The vertical post is secured by three cables. The cables are pre-tensioned so that the resultant of the cable forces F, Q, and P is directed along the z-axis. If F = 120 N, find P and Q.
200 N 825 i 400 N 825 mm 1800 min 200 N 1650 mm 250 N 350 N
Ea-300 200 4S 30k 30 930 ニ 400MS X- E = ? Ego? Y ? e E,=? Eq=? Bq=?
Engineering MechanicsChoices:DF:243.31 N (C)243.31 N (T)233.31 N (C)233.31 N (T)EF:134.16 N (C)134.16 N (T)154.16 N (C)154.16 N (T)EG:360 N (C)360 N (T)320 N (C)320 N (T)
Use 700 at the Place of RN
WhatsApp .ll 3G 9:44 AM 81% Assignm. Assignment A steel tape of nominal length 30m was used to measure a line AB by suspending it between supports. The following measurements were recorded tension applied Line Length measured slope angle mean temperature 3°40 AB 29.872 120N The standardized length of the tape against a reference tape was known to be 30.14m at 20° and 50N. If the tape weighs and has a cross sectional area of 2mm?, calculate the horizontal length of AB. Young's modulus (E) for the tape is 200 and the coefficient of thermal expansion (a) is 0.0000112 per °C
1500 16 1500 16 153016 28o e ol to ee nm oideshun 12 40006 300016 4000 IL Determine th- Force in member AB, AC, BL, BD and CD
1:49 A ה 5% ll ,ll > וN 1.jpg Area Wire Diameter in sq. mil cir. mil MCM mm A 1.02 mm B (51/1270) in 40.1575 mil II
Table 4: Measurement of Horizontal Distance on Level Ground DISTANCE TRIAL MEAN DISCREPANY PRECISION FORWARD BACKWARD A-1 10 10 2-3 10 10 3-4 10 10 4-5 10 10 74.335m 0.005m 1/1486 5-6 10 10 6-7 10 10 7-B 4.34 4.33 2. The discrepancy for the measurement is the difference between the first measurement and the second measurement.
4.791 Bm 15 71.589° THOT # 8.629 Tpt 12.124 7.2.32 Tp-3 1678 5,643' 1.747' Bm 39 тр-2 Place data in the form of field notes. Include the arithmetic check. Assuming the average length of each BS and FS is 125ft. determine the order of accuracy. of closure for construction projects. Use the evver 2.932' Constraction site
(b) Two connected steel bars as shown in Figure Q2(b) are axially loaded with 100 N at node 3. The cross section area for bar B is half of bar A. The horizontal displacement at node 2 is half of displacement at node 3. By using finite element method, determine the displacement at node 2 and node 3. The modulus of elasticity is constant.
ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LNG EXPLANATION. ANSWER IN 2 DECIMAL PLACES.) 9.82 Compute the ¯Ix and ¯Iy for the annular region.(Ans: Ix = 4.084 × 106 mm4, ¯Iy = 0.816 × 106 mm4)