A pitot tube is used to measure the flow rate of air at a temperature of 500 K inside a duct. If the measured static pressure was 200 kPa, the measured stagnation pressure was 223 kPa and the air can be treated as an ideal gas what is the air velocity?

A pitot tube is used to measure the flow rate of air at a temperature of 500 K inside a duct. If the measured static pressure was 200 kPa, the measured stagnation pressure was 223 kPa and the air can be treated as an ideal gas what is the air velocity?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The Mach number is unity at the location of smallest flow area, called the * O Venturi nozzles O throat O diverging nozzles
Air is allowed to flow from a tank with temperature of 69.8 °F and with pressure of 49.3461 atm through a pipe. It was measured that flow rate is 2.2046 lbm/sec. At some point on the tube static pressure pressure was measured to be 22501.845 mmHg. Assume that process is isentropic and neglects the velocity at the reservoir, calculate the pipe diameter (answer in whole number, unit is mm). Assumed that the ratio of specific heats is 1.4.
This error occurs if the airflow is not directly parallel with the pitot-static tube 1. Compressibility Error 2. Instrument ErroR 3. Position Error 4. None of the above
y aer. A Pitot tube is used to measure the air flow rate in a eircular duct 8.5 m I.D. The "riowing air temperature is 65.5°C. The Pitot tube is placed at the center of the duct and the reading R on the manometer is 1.2 cm of water. A static pressure measurement obtained at the Pitot tube position is 2.0 cm of water above atmospheric. Take Cp 0.98,9ter ase press u = 2.03 x 10 Pa.s, if U- Ux ( 1-0.17). Calculate The velocity at the center and the average velocity. The volumetric flow rate of the flowing air in the duct
Question 11: A non-flat plate is placed inside a wind tunnel where the air velocity in the test section is set at 0.5 m/s. Pitot tube is used to measure the difference of static and stagnation pressure, which is converted to find the velocity. The pitot tube is placed above the flat plate and can be adjusted in the direction perpendicular to the flat plate to measure the air velocity parallel to the flow in the boundary layer. Suppose the velocity at the middle of the boundary layer thickness is measured as 0.35 m/s, determine the relation of boundary layer thickness, displacement thickness, and momentum thickness to the distance from the leading edge using approximation method if the velocity profile is (a) linear, and (b) parabolic.
For a moving normal shock wave the gas velocity represents the y-velocity when the normal shock wave was stationary True Or flase
10x106 ft3 of a gas at 60 °F and 760 mmHg must be delivered to a power plant per 24-hr day from a company 5 miles away. Delivery conditions are to be 60 °F and 10 psig at the plant. a. If the gas leaves the compressor at a temperature of 75 °F, what must be the pressure (in psia) at this point? The pipe is stainless steel with 20 inch Inner Diameter.
Show and expalin all steps in solution.Iso-butane at initial temperature of 10C is flowing with the entry velocity of 5 ft/s inside the pipe of 2 inch diameter. At the exit the diameter of the pipe is enlarged to 5 inches. The height change from the initial to final stage is 2 ft. Local gravity is 32.0 ft/s2. The initial pressure is 1.5 bar. Make a Temperature-Volume plot showing all pressures, temperatures and stages. What is mass flow rate in lbm/s? Use NIST to find the density at the inlet. What is the exit velocity of the stream in ft/s if the temperature of the iso-butane is the same, but pressure drops to 1.45 bar? What is internal energy change? Was heat added or removed from the pipe?
Air flowing through a 500 mm diameter duct the U-tube static pressure reading is 5 mm H2O W.G. and total pressure is 9 mm H2O W.G. What is the air flow velocity?
liquid pentane with relative density 0.62, 20 °c as shown in the figure at temperature, the geyç pressure is 0.2 atm dollars a cast iron (0.2 m odiameter cast iron)) it flows through the pipe.Marked as full pipe output it can be considered as the principal atmospheric pressure at the point at which it is. The total pipe length in the system is 45 m.5 kW in the system there is a pump that works with 92% efficiency in its power. Liquid since the volumetric flow rate of pentane is 0.05 m2 / s, with the tank calculate the height difference botween the pipe output. Data: * Friction loss at the pump is negligible. Gryc Atark purmp
Air is flowing in a duct with velocity of 7.62 m/s and static pressure of 2.7 cmWG. The duct diameter is 1.22 m and the barometric pressure is 99.4 kPa and the gage fluid temperature and air temperature is 30 degC. What is the total pressure against which the fan will operate in mm of water? and What is the required motor brake power in Question no. 4 assuming a mechanical efficiency of 89%.
An industrial nozzle as shown in Figure 3 works with an inert gas rush through the nozzle where the speed of the gas at the nozzle throat is recorded equal to the speed of sound. The inlet velocity, temperature, and pressure are 98 m/s, 600 oC, and 88 psi, respectively.Take the property of inert gas for k = 1.66 and cp = 5.192 kJ/kg. K. Calculate:a) Stagnation pressureb) Mach number at the nozzle inletc) Temperature of the gas at the throatd) Pressure of the gas at the throat