A pressure vessel of 225-mm inner diameter and 6-mm wall thickness is fabricated from a 1.2 m section of spirally welded pipe AB and is equipped with two rigid end plates. The gage pressure inside the vessel is 2 MPa, and 45-kN centric axial forces P and P' are applied to the end plates. P' A 1.2 m 35⁰ B Determine the shearing stress parallel to the weld. The shearing stress parallel to the weld is P MPa.

A pressure vessel of 225-mm inner diameter and 6-mm wall thickness is fabricated from a 1.2 m section of spirally welded pipe AB and is equipped with two rigid end plates. The gage pressure inside the vessel is 2 MPa, and 45-kN centric axial forces P and P' are applied to the end plates. P' A 1.2 m 35⁰ B Determine the shearing stress parallel to the weld. The shearing stress parallel to the weld is P MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A welded steel cylindrical drum made of a 10-mm plate has an internal diameter of 1.20 m. Compute the change in diameter that would be caused by an internal pressure of 1.5 MPa. Assume that Poisson's ratio is 0.30 and E = 200 GPa. OLAd 0.459 mm OIL. Ad Ⓒ III. Ad = 0.289 mm ON. Ad 0.369 mm 0.521 mm
The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 700 mm and a wall thickness of 8.9 mm. For a gage pressure of 1.27 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume = 51. s Answers: (a) Normal stress= (b) Shear stress - MPa MPa
The pressure tank shown is fabricated from spirally wrapped metal plates that are welded at the seams at an orientation of Assume B = 62.5. The tank has an inside diameter of d- 1800 mm and a wall thickness of t-7 mm. For a gage pressure of p-0.8 MPa, determine (a) the normal stress perpendicular to the weld and (b) the shear stress parallel to the weld. (a) on MPa (b) Tnt" MPa
A 50 inches diameter storage tank is used to store air at an internal pressure of 625 psi with a FS = 4.5 based on ultimate strength. If the welded joints have a joint strength efficiency of 80% and the steel used to create the tank hasan equivalent strength similar to C1118,a. find a suitable plate thickness of the tank. Compare the stresses for both diametral section and longitudinal sectionb. Using the thickness solved in (a), determine the pressure to cause actual failure to the vessel
A cast Aluminum crlinder o f a Portable hodrawlic 208 Mm in diameter The 16,8 N/mm2 by gauge riveter is Pressure. of The fluid is Determine Sui table thicknesS of the inder wall assuming that the Yield Point stress 442 N/mm2 And factor of safety of 6.2 Calculate. the tangential and radial streses middle radius and at the inner outer surface.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 3.10 ksi.
A 1.7 m diameter closed cylinder 2.7 m. high is completely filled with glycerin SG is 1.65 under the pressure of 230.25 kPa at the top. The steel plates which form the cylinder are 16 mm thick and can withstand allowable tensile stress of 82300 kPa. Compute the maximum pressure at the bottom of the tank to resist hoop tension if it is rotated about its vertical axis. 01594.18 kPa 01549.18 kPa 01459.81 kPa ONone of These O1495.81 kPa
Q3: (a) describe the location and function of the following: \i. Gudgeon pin ii. Rod shank ii.Large end (b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is approximately 3.2N/mm. Design the studs also for the cylinder cover. Assume the allowable hoop stress =42 N/mm' for cast iron; the allowable tensile stress for material of studs =63 N/mm?
The steel pressure tank shown has a 30-in. inner diameter and a 0.375-in. wall thickness. It is given that the butt-welded seams form an angle β = 50° with the longitudinal axis of the tank and that the gage pressure in the tank is 200 psi. Determine the normal stress perpendicular to the weld. Determine the shearing stress parallel to the weld.
The closed thin-walled tank has an inner radius of r and wall thickness t and contains a gas of pressure of p. The state of stress at point "a" on the surface of the tank is represented by stress components with an unknown stress element rotation angle of 0. Note that, the two normal stress components for x'y' system (note: not xy system!) are known: ox, = 120 MPa and Oy = 180 MPa, but the shear stress component (T,) is unknown. Determine: (1) the principal stresses at point a ; (2) Tx'yı ; (3) rotation angle of 0 . y 180 MPa 120 MPа х 0 = ? a Tyy = ? tank cross section stress state at point a
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 325 psi, determine the magnitude of the shear stress parallel to the weld. O 611 ksi O452 ksi O 653 ksi O 3.77 ksi O 495 ksl
Welded seams A cylindrical tank with a semi-spherical head as shown. Tank diameter is 1.5 m, the thickness is 20 mm, and internal pressure is 2.0 MPa. The maximum stress in the heads of the tank is approximately: * S 45 MPa 37.5 MPa 50 MPa 59 MPa 25 MPa None of the above