A simply supported beam of dimension 12 m x 45 mm x 65 mm. It carries a uniformly distributed load of 450 kN/m for entire span. Determine (a) Maximum stress due to bending and (b) Young's modulus of the material used for the beam, if it deflects 150 mm maximum at the mid of the span. Also find the maximum slope in the beam. (Enter only the values by referring the units given, Also upload your hand written answers in the link provided) Moment of inertia of the cross section of the beam in m4 = Young's modulus of the beam material in MPa is = Maximum bending stress due to bending in MPa is =

A simply supported beam of dimension 12 m x 45 mm x 65 mm. It carries a uniformly distributed load of 450 kN/m for entire span. Determine (a) Maximum stress due to bending and (b) Young's modulus of the material used for the beam, if it deflects 150 mm maximum at the mid of the span. Also find the maximum slope in the beam. (Enter only the values by referring the units given, Also upload your hand written answers in the link provided) Moment of inertia of the cross section of the beam in m4 = Young's modulus of the beam material in MPa is = Maximum bending stress due to bending in MPa is =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simply supported beam of span 3.0 m has a cross-section 120 mm × 180 mm. If the permissible stress in the material of the beam is 10 N/mm², determine () тахітит udl it can сarry (ii) maximum concentrated load at a point 1 m from support it can carry. Neglect moment due to self weight.
A simply supported beam of span 3.0 m has a cross-section 120 mm × 180 mm. If the permissible stress in the material of the beam is 10N/mm2,determine(i)maximum udl it can carry (ii) maximum concentrated load at a point 1 m from support it cancarry. Neglect moment due to self weight.
Calculate the values and plotthe shear stress distributlon. 3 Maximu tensile and maximum Compressive stresses in the beam sectlon. Plot the normal stress distribution by 50 mm 57 KNM M. 84 mm В 38mm 76KN 150 mm O Thelocation centes of grauity of the beam sectlon and x passing throuch the centes of grovituy.Calculate the moment of inestia arbout the axis Shear stress Qt points A,B,C,G and Dof the beam section. calculading.
consider the beam shown in. EI is constant. assume that EI is in kip * ft2. determine the expression for the elastic curve using the coordinate x1 for 0 < x1 < 20 ft, where x1 is in feet. v1 in ft answer in terms of the variables x1, E and I. determine the expression for the elastic curve using the coordinate x2 for 0 < x2 < 10 ft where x2 is in feet. v2 in ft. answer in terms of the variables x2, E and I. specify the deflection of the beam at C. vc in ft. answer in terms of E and I. specify the slope at A, measured counterclockwise from the positive x1 axis. Theta A in rad. answer in terms of E and I.
The simple beam shown supports the uniformly distributed load with intensity wo = 300 N/m. The span of the beam is 1.2 m. Determine the value of Ely, in N-m³, at midspan. wo 1/2 Ro
A timber beam of rectangular section carries a load of 2 kN at mid-span. The beam is simply supported over a span of 3.6 m. If the depth of section is to be twice the breadth, and the bending stress is not to exceed 9 N/mm2 , determine the cross-sectional dimensions.
1 kN 12. A cantilever beam AB, loaded by a uniform load and a 320 N/m concentrated load, is constructed of a channel section. Find the maximum tensile stress o, and maximum compressive stress ac if the cross section has the dimensions indicated and the moment of inertia about the z axis (the neutral axis) is I = 130 cm*. Note: The uniform load represents the weight of the beam. 1.5 m 15 mm [ Ans : a, = 105.8 MPa ; 6e = 28.8 MPa ] 55 mm
In a 2.5 cantilevered I-beam, 2500 kg weight is applied at 0.75 meter from the free end. If the allowable stress in beam is 120 Mpa, determine the section modulus and The base and height of the beam if the base is 75% of its height mm.
Determine the minimum allowable height (h) in mm of the beam shown in the figure if the bending stress is not to exceed 20 MPа. 5 kN 2.5 kN/m 80 mm A E D 1.0 m 1.0 m 2 m
Determine the maximum tensile and compressive stresses developed in the overhanging beam that is loaded and has the cross- sectional properties as shown. 1600 lb 4000 lb 2 in N.A. 6 in 6 ft R I- 90 in 6 ft tensile stress = 3, 840 psi and compressive stress = 7, 680 psi tensile stress = 1, 280 psi and compressive stress = 2,560 psi tensile stress = 7, 680 psi and compressive stress = 3, 840 psi tensile stress = 7, 680 psi and compressive stress = 2, 560 psi
A simply supported beam of dimension 12.5 m x 35 mm x 70 mm. It carries a uniformly distributed load of 450 kN/m for entire span. Determine (a) Maximum stress due to bending and (b) Young’s modulus of the material used for the beam, if it deflects 150 mm maximum at the mid of the span. Also find the maximum slope in the beam. Moment of inertia of the cross section of the beam in m4 = oung's modulus of the beam material in MPa is = Maximum bending stress due to bending in MPa is = The slope at the supports of beam in radians is =
Consider the reinforced cConcrete beam shown. The 250 mm beam is subjected to a positive bending moment of 175 kNm. Determine the stress in the steel and the maximum stress in the concrete. Use E=2.5 GPa for the concrete and 200 GPa for the steel. Use concrete as the reference material. I mm4 O po o SO mum Ost MPa (Ocon)max 4 pcs. MPa 20mmø Please follow this format in answering. Given: Required: n I in mm4 Ost in MPa (O con)max in MPa Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used) After the computation, provide an explanation (in words) of how you solve the problem; the step-by-step process that you took, the strategy, etc. W ost