A uniform disk of mass m = 4 kg and radius r = 150 mm is supported by a belt ABCD that is bolted to the disk at B and C. If the belt suddenly breaks at a point located between A and B, draw the FBD and KD for the disk immediately after the break.

A uniform disk of mass m = 4 kg and radius r = 150 mm is supported by a belt ABCD that is bolted to the disk at B and C. If the belt suddenly breaks at a point located between A and B, draw the FBD and KD for the disk immediately after the break.

Name: A uniform disk of mass m = 4 kg and radius r = 150 mm is supported by
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A uniform disk of mass m = 4 kg and radius r = 150 mm is supported by a belt ABCD that is bolted to the disk at B and C. If the belt suddenly breaks at a point located between A and B, draw the FBD and KD for the disk immediately after the break.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.5P: The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw...

See similar textbooks

Similar questions

The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
End B of the uniform 2.7-kg bar AB is connected to a small roller that moves in a horizontal slot. The other end of the bar is pinned to the homogeneous 1.8-kg disk that rolls without slipping on the vertical surface. The spring attached to A has a free length of 0.3 m and a stiffness of 58 N/m. After the system is becomes horizontal. Determine the magnitude of the force P that acts on the bar at B. 2.1 m 0.24 m 0.9 m www 1.8 kg 1.5 m 2.7 kg P
The hand brake for a bicycle is shown. Portions DE and FG are free to rotate on bolt A which is screwed into the frame BC of the bicycle. The brake is actuated by a shielded cable where T1 is applied to point E and T2 is applied to point G. A spring having 40 N compressive force is placed between points E and G so that the brake stays open when it is not being used. Assume the change in the spring's force is negligible when the brake is actuated to produce the F = 100 N forces at points D and F. Determine the necessary cable forces T1 in N.
A baseball attachment that helps people with mobility impairments play T-ball and baseball is powered by a spring that is unstretched at position 2. The spring is attached to a cord that is fastened to point B on the 75-mm radius pulley. The pulley is fixed at point O , rotates backwards to the cocked position at 0 , and the rope wraps around the pulley and stretches the spring with a stiffness of k = 2000 N/m. The combined mass moment of inertia of all the rotating components about point O is 0.40 kg·m2. The swing is timed perfectly to strike a 145-gram baseball travelling with a speed of V0 = 10 m/s at a distance of h = 0.7 m away from point O. Knowing that the coefficient of restitution between the bat and ball is 0.59, determine the velocity of the baseball immediately after the impact. Assume that the ball is travelling primarily in the horizontal plane and that its spin is negligible.
The mobile crane is symmetrically supported by two outriggers at A and two at B in order to relieve the suspension of the truck upon which it rests and to provide greater stability as shown in. Suppose that the crane and truck have a mass of 18 Mg and center of mass at G1, the boom has a mass of 1.8 Mg and center of mass at G2. The boom is supporting a load having a mass of 1.4 Mg. Determine the positive critical angle 0max (in degree) where tipping starts to OCcur. 6.25 m INI 2 m T1mlm
A Tractor of mass 1200kg is used to lift gravel weighing 8KN. Determine the reaction at each of the front wheel.
4. The rigid link is supported by a pin at A, a steel wire BC having an unstretched length of 300 mm and cross-sectional area of 20 mm², and a short aluminum block having a length of 100 mm under no load and cross-sectional area of 40 mm². If the link is subjected to a vertical force of 550 N as shown, determine the force in wire BC and the aluminum block, and the rotation of the link about pin A. Est = 200 GPa, EA = 70 GPa. 300 mm B 200 mm 550N 250mm D A 250 mm 100 mm
The 15-lb bar BC is connected to a disk centered at A, and to a bar DC. If the disk is made to rotate at a constant speed of 180 rpm, determine the vertical components of the force exerted on bar BC at B and at C.
The 12ft pole AC (negligible mass) lies in the y-z plane and forms a 30° angle with the z-axis. The pole is held in place at point C by a ball-and-socket joint. Two cables, BD and BE, are fixed to the pole at point B (these represent two separate cables attached at B). A 110 lb force pulls downward at the end of pole AC in the vertical direction (y-direction). If the distance between B and C along the feet, determine the Reactions at C (ball-and-socket joint) The tension in cables BD and BE.
Two uniform disks A and B, each having a mass of 4k, are connected by a 3kg rod CD, as shown in the figure. A counterclockwise torque M of 4 N*m is applied to disk A. Knowing that the discs roll without slipping, determine the horizontal component of the force that pin D exerts on disc B. The answer is Dx= 8.66N to the left
The compound pulley shown has a weight of 1600 N and the radius of gyration (k = 2 m). Find the tension in the cord supporting the 1500-N weight (TA) and tension supporting the 2000-N weight (TB) as shown
1. An excavator encounters a reaction force of 7600 lb from the ground, normal to line AC, as shown. The shaded structural members (Dipperstick (FH), Mainboom (ADK), bucket, and hydraulic cylinders) have a combined weight of 15000 lb and a horizontal mass center located midway between points C and G. ΑΠΟ G 3 ft 6 in. 40° E Mainboom 3 ft 4 in. 39 ft Dipperstick H Bucket 7600 lb C ANNAL Questions: (a) Dismember the shaded structural members (with labeled points A-H) from the tractor and sketch a free-body diagram showing external and exposed internal forces. (b) Compute the force in the hydraulic cylinder strut BD and the pin reactions at A in the given position.