Please answer asap T_T A rectangular beam has a width of 353 mm and an effective depth of 602 mm The specified compressive strength of sand-ightweight concrete is 26 MPa and the vield strengti of stirups is 319 MPA Determine the required spacinE ofvertical stirups when the required shear strength V is 219 KN, The diameter of stimups is 10 mm Round down the spacing by multieles of S mm.

As per IS 456 2000 S=0.87×fy×Asv×dVuss=spacing of stirrupsfy= yield strength of sttirups=319…

Arectangular beam has a width of 353 mm and an effective depth of 602 mm. The specihed compressive strength of sand-lightweight concrete is 26 MPa and the yeld strengh of stimups is 319 MPa Delennine the maared socng of vertical stimups when the required shear strength Vis 219 AN. The dameter of stimips is 10 mm. Round down the spacing by multieles of S mm.

Arectangular beam has a width of 353 mm and an effective depth of 602 mm. The specihed compressive strength of sand-lightweight concrete is 26 MPa and the yeld strengh of stimups is 319 MPa Delennine the maared socng of vertical stimups when the required shear strength Vis 219 AN. The dameter of stimips is 10 mm. Round down the spacing by multieles of S mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation . Ust Bearing |1000 kN plate Steel- Concrete 300 mm 300 mm Section a-a
The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7 wires of 6 mm dia strand and stressed to 800 MPa has to be anchored at the center of the block. The anchorage plate is 75 mm x 75 mm. If the concrete mix is M45 and the permissible bending stress in M. S. steel plate is 165 MPa, determine the thickness of the anchorage plate.
A rectangular beam has a width of 258mm and an effective depth of 600mm. It is reinforced with 4-36mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 279MPa. The depth of the concrete stress block is ___ mm.
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340 mm Thickness of flange tf = 140 mm Effective depth d = 350mm Effective concretee covering d' = 75mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = _________ mm2
A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If fc= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm
A rectangular cantilever beam has a width of 250mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The depth of the concrete stress block is?
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars, Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MP.. 640 mm 800 mm 6 #32 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. = 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength of fy = 360 N/mm. The spirals are d 10@50 with the yield strength of fy = 270 N/ mm. If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.
a-Design the concrete column to carry the applied load Concrete allowable strength: 35 MPa P= 900 kN Column dimension needs to be 300 mm X B Material reduction factor 0.75 - Load factor 1.5 B mm 300
A rectangular beam has a width of 269mm and an effective depth of 600mm. It is reinforced with 4-36mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 285MPa. The depth of the concrete stress block is ___.
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars. Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPA. 640 mm 800 mm 6 #32 C 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force