Assignment No. 01 A simply supported deep beam has a clear span equal to 3660 mm, a total height equal to 1830 mm, and a width of 460 mm. The beam supports an 460 mm.-square column at midspan carrying a dead load equal to 1335KN, and a live load equal to 1068KN. Column: 460mmx460mm DL=1335 kN LL= 1068 kN 1830 mm Design the beam using the strut-and-tie model, using fc equal to 28MPA and fy equal to 420 MPa. 1830 mm 1830 mm Column: 460mmx 460mm Column: 460mmx460mm

Assignment No. 01 A simply supported deep beam has a clear span equal to 3660 mm, a total height equal to 1830 mm, and a width of 460 mm. The beam supports an 460 mm.-square column at midspan carrying a dead load equal to 1335KN, and a live load equal to 1068KN. Column: 460mmx460mm DL=1335 kN LL= 1068 kN 1830 mm Design the beam using the strut-and-tie model, using fc equal to 28MPA and fy equal to 420 MPa. 1830 mm 1830 mm Column: 460mmx 460mm Column: 460mmx460mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the Bar Forces FMJ nnd FoE (section method), and one Zero member; Show all F.B.Ds. к L H 4m M N 4m D E G в C F A 80KN 100KN 8m 8m 8m 5m 8m
H.W :- 103 the simply supported beam shown below carries the factored louded indicated. Using f'c = 20.7 N/mm² and fy = 276 N/mm", design and detail the required vertical stirrups W₁ = 100kN/m ₁Pu= lookN 700 Vc = |d=630 $70 Vc = 126 + 350 Vudface of support = wuln, lu 2 100X6 + 10 = 350k 2 2 Sie bud 6 √ 2017 Vuo distanced from face. of support = 350 - wud Vud: 350-100x6+63 = 287 kN 4 * x 350 X630 350 KM ( ( 3m 3m 6m (clear span), =167.2KN 1000 Uc= 0.75X 167.2 = 125.4 KN // $U = = x 125.4 = 62.7 KN 2 52 Sok
H Y G F 30 kips 20 30 kips- C D 40 kips 40 kips 40 kips 50 kips 70 kips 4 @ 15'= 60'- (a) Section Method
A steel beam having a span of 14 m. carries a dead load concentrated load Pp = 60 kN at its midspan. The beam is laterally supported at its span. Properties of the wide flange section. rts - 104.39 mm ho - 338.08 mm Jo -1.69 x 10^6 Cw - 4.3 x 10^12 d=356.11 mm tf = 18.03 mm tw - 11.18 mm Sx - 2343 x 103 mm rx = 155.96 mm ry - 93.98 mm Sy = 818 x 10^3 mm Zx = 2573 x 10^3 mm Zy= 1239 x 10^3 mm Fy = 345 MPa Iy = 151 x 10 mm Lp=3.98 Lb=14m Lr=12.98 Cb=1.14 Determine the safe concentrated live load that the beam could support at the center based on its design strength
Question 2 Using the Method of Sections find the force in member JK. 15 kips 20 kips 20 kips 10 kips C D Ligh K H A B J 6 bays @ 15'-0" = 90'-0" Upload Choose a File M G N 12'-0"
The wooden members in the simple truss below have the following capacity: Shear parallel to grain = 1 MPa, Compression parallel to Grain = 11MPa, Compression perpendicular to Grain = 5 MPa 1. Find the minimum safe x. a. 73 mm b. 160 mm c. 148 mm d. 112 mm 2. Find the minimum safe y. a. 15.97 mm b. 19.45 mm c. 9.14 mm d. 18.28 mm 3. Determine the stress in member AC. a. 1.13 MPa b. 1.258 MPa c. 1.224 MPa d. 1.04 MPa
M Inbe x Qui: x t T2 x C X O FO x E PLA X PLAX Plat x I PLS x 0x 卡 feu.instructure.com 2. Compute the maximum unsupported length of the simple beam to adequately support the given unfactored loads. Use f'c=21MPa, fy=D415MPA, f,-10mm, and cc350mm. 250 mm Pu Loads: WDL=10KN/m WLL=30KN/m PDL-40KN PLL-60kN Wu A. BO 400 mm 3-28ф KL/2 L/2 Edit View Insert Format Tools Table 12nt Paragranh A. A 4) O ENG 1:59 pm
Design the shear Reinforcements of the following beam using only two stirrup spacings and draw the details of your design. The loads shown are factored loads. Neglect the self-weight. 600KN Given 220KN Width of beam: 500mm Effective Depth (d) 630 mm f. = 28 MPa fy 420 MPa 2.0m 4.5m Stirrups : Ø10mm -8.0m
500 mm 62.5 mm 375 mm 62.5 mm P. Determine the total required number of 20mm bars to be used in two end faces only for the 300mm x 500mm rectangular column shown to support the following loads: Pu = 800 kN Mu = 120 kN-m Use f'c = 20.7 MPa and fy = 413.7 MPa Use 1 ksi = 6.893 MPa %3D 300 mm O O O O
Select required unifform stirrup spacing for the beam shown? PL=100 kN 350 mm Wo=35 kN/m 8#29 3.0 m 3.0 m f'c = 20 MPa, fy= 420 MPa, Use bar #10 A) 540 mm B) 350 mm C) 250 mm D) 300 mm 5. 600 mm 670 mm
This problem is about replacing the loading system acting on the beam shown below by a resultant force and a couple moment at acting at Point O. Oppfz 350 lb-ft 50pff ∙100th £40016 Determine: a) The resultant couple moment (MRO). Provide the direction of rotation (CW or CCW). b) The component of the resultant force in the x-direction (FRx). Provide the direction of the force. c) The component of the resultant force in the y-direction (FRY). Provide the direction of the force.
Draw SFD and BMD for the single side overhanging beam subjected to loading as shown below. Mark salient points on SFD and BMD. -60KN/m 20KN 20KN/m A TAMIPAL Inspired by life C B D 3m 2m 2m