(b) An induction motor shaft, running at 1400 RPM as shown in Figure Q2 (b) drives an intermediate shaft by a flat belt drive. The diameter of the pulley on the motor shaft is 400 mm and that on the intermediate shaft is 700 mm. Another pulley of diameter 450 mm drives an output shaft, having a pulley 650 mm keyed to it. If there is 5% slip each belt drive, examine the final speeds of the output shaft. (6 marks)

(b) An induction motor shaft, running at 1400 RPM as shown in Figure Q2 (b) drives an intermediate shaft by a flat belt drive. The diameter of the pulley on the motor shaft is 400 mm and that on the intermediate shaft is 700 mm. Another pulley of diameter 450 mm drives an output shaft, having a pulley 650 mm keyed to it. If there is 5% slip each belt drive, examine the final speeds of the output shaft. (6 marks)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(d) A motor drives the winch drum through a reduction gear with a gear tooth ratio of 0.1 as shown in Figure Q1(d). The friction torque at winch shaft is 15 Nm and at the motor shaft is 10 Nm. At the motor speed of 1500 rpm, the winch complete one rotational cycle in 11 s. (i) Calculate the equivalent moment of inertia of the drive referred to the motor shaft. (ii) Examine the motor torque if the gear and winch has efficiency of 90% and 98%, respectively. (iii) Find total power of the motor. Winch 0.2 m radius Motor Jo = 0.5 kgm? Gear Cable Jg = 0.15 kgm? at the motor speed Load 500 kg Figure Q1(d)
A blower is driven by an electric motor though a belt drive. The motor runs at 750 r.p.m. For this power transmission, a flat belt of 8 mm thickness and 250 mm width is used. The diameter of the motor pulley is 350 mm and that of the blower pulley 1350 mm. The center distance between these pulleys is 1350 mm and an open belt configuration is adopted. The pulleys are made out of cast iron. The frictional coefficient between the belt and pulley is 0.35 and the permissible stress for the belt material can be taken as 2.5 N/mm2 with sufficient factor of safety. The mass of a belt is 2 kg per meter length. Find the maximum power transmitted without belt slipping in any one of the pulleys.
A blower is driven by an electric motor though a belt drive. The motor runs at 750 r.p.m. For this power transmission, a flat belt of 8 mm thickness and 250 mm width is used. The diameter of the motor pulley is 350 mm and that of the blower pulley 1350 mm. The center distance between these pulleys is 1350 mm and an open belt configuration is adopted. The pulleys are made out of cast iron. The frictional coefficient between the belt and pulley is 0.35 and the permissible stress for the belt material can be taken as 2.5 N/mm2 with sufficient factor of safety. The mass of a belt is 2 kg per meter length. Find the maximum power transmitted without belt slipping in any one of the pulleys. Note: Sketch the belt drive system for both parts and label the given data on it.
In the figure below, a motor with power 150kw and speed of 2500 rpm is connected to shaft 1(by coupling) in a clockwise direction. Shaft 2 is connected to shaft 1 by gears 1 and 2. If 30% of the power is consumed by the gear3 and 9% by the pulley and 61% by the sprocket, draw torque diagrams for both shafts. If the pressure angle of the gears is 20 degrees to the x-axis, Calculate the reaction forces of the bearings and draw the bending moment diagrams for both shafts according to the information below: Lengths: AB=90mm/BC=DGH=50mm/CD=HI=60mm/DE=IJ=80mm Diameters: dG1=dG2=47mm/ dG3=20mm/ d(pulley)=35mm/d(sprocket)=40mm Gears Gear2 Tew) shaftz Bearing Shaft Gear1 SProcket
Note: If you don't know the solution please leave it but don't give me wrong solution. A flat open belt drive is used to transmit a power of 25kW from a motor shaft rotating at 950 rpm. The radius of the pulley of the motor shaft is 125mm while the radius of the puller of the driven shaft is 450mm. The center distance between the shafts is 2,250mm. the coefficient of friction is 0.25 and the density of the belt material is 950 kg/m^3. The belt width is 126 mm. The allowable stress is 2.6MPa. Determine the thickness of the belt.
A hammer mill is driven by a High Torque (HT) AC motor. The system is used for 8 hours /day. Input speed is 870 RPM and input power is 25 HP. Nominal output speed is 310 RPM. Design a V-belt drive and specify:(a) (b) (c) (d) (e)the belt size,the sheave sizes,the number of belts, theactualoutputspeed,the center distance. Show all your calculations.
Problem 4 The compound gear train of a three stages reduction gear is use to transmit power from a power source to a drum with 1 meter in diameter, as shown in Figure P4. The power source generates 500 Nm torque at the speed of 500 rpm and can produce acceleration of 10 rad/s?. Assume there is no friction in the drum, mass of the cable is negligible and the cable is in-elastic. With this condition, determine the folbwing. i. ii. iii. Angular vebcity and acceleration of the drum. Power required to overcome the friction torque in the bearing. Power required to accelerate the inertia of the gear system. Load M that the drum can lft. N. [1.05 rad/s; 0.2 rad/s ; 1.13 kW ; 2.12 kW ; 3,221.7 kg] Drum2 (2) Drum 1 Power A source 凶凶 (1) Load, M (4) Figure P4 Given:- Number of gear teeth, t:- t;=40 ; t2=100 ; t;=40 ; t4=160 ts=40 ; t6=200 Equivalent mass moment of inertia, Ieq:- Ipower source=2 kgm ; Igear 23=10 kgm2 ; Igear 45=20 kgm2 ; Igear 6 & drum=40 kgm? Friction torque in bearing, F:-…
A 25-hp. 1750-rpm electric motor drives a machine through a multiple V-belt. The size 5V belts has unit weight of 0.012 lbf/in.) The pulley on the motor shaft has a 3.7-in. pitch diameter and geometry is such that the angle of wrap, o is 165º. k is consenvatively assumed that the maximum belt tension (F1) should be limited to 150 lbf, and that the coefficient of friction will be at least 0.512. [Hints: Use equations 17.18, 17.21, (h)]
A 2hp motor is to drive a food shredder. The motor is projected to run at 1450 rpm and the required speed at the food shredder is 60 rpm. Design a double reduction drive consisting of belt and chain for this application. Please give solution and show drawing if needed
A (25 kW, 500 rpm) motor has a mild steel shaft of (30 mm) diameter and (8 cm) length. There are two parallel keys available A (w = 12 mm, t = 10 mm) and B (w = 10 mm, t = 8 mm), suggest one of them to connect the shaft with a pulley. use torsional shear stress = 160 MPa, tensile strength = 400 MPa, compression strength=280 MPa, bending strength= 380, factor of safety=3. Hello, I need an accurate handwritten answer in 15 minutes, please
A 60 hp air pump blower in 18hr/day service running at a speed of 500 rpm is driven by means of a multiple v-belt drive which is powered by a compressor-stator motor with speed 1300 rpm. The center distance must be between 30 to 40 inches and the available driver sheave diameter iS 14 inches. Recommend a multiple v-belt drive that respects the following condition stated.
A spur pinion rotating at 20 rad/sec and having 20 teeth transmits 20 kW to a gear wheel. The pressure angle is 20° and module is 20mm. The reaction exerted by the pinion at the centre of thc shaft is