b) Derive a block diagram model for the RLC series circuit shown inFigure Q1, relating input voltage Vin to output voltage Vout derivedacross the inductor. Your answer should identify the statevariables, list the governing equations, and clearly show thedirection of flow of signals in the block diagram.R+Vin(~CFigure Q10.000Vout

Answered: Image /qna-images/answer/f6b9ac64-3621-49b9-8144-c7a168dad890.jpg

Answered: b) Derive a block diagram model for the…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit below with input voltage V1, a step function of magnitude 25 volts at time t-0, find the transient response voltage across the capacitor C1 and plot the results: (Provide your calculations and reasoning for your answer.) R1 555 250mH V1 = 0 V2 - 25 TD = 0 TR In V1 C1 TF in PW- 25 PER = 3.3u
Consider a circuit with a pull-down resistor in parallel to a component. Compare a resistor with higher resistance value to a resistor with lower resistance value in the parallel path. Which resistor value will pull down the potential more, relative to ground, at the high side of the component? They will pull the potential di [ Select] They will pull the potential down equally, because resistors in series have equal voltage across them, regardless of resistance value. The lower-value resistor. There is not enough information to correctly answer this question. The higher-value resistor.
A particular circuit built with one resistor and one capacitor in series allows high frequency source voltage sine waves to be transmitted as the output essentially unchanged. Any low frequency source voltage sine waves are “killed”; the output is very small, essentially zero. Design this circuit: draw the circuit and explain whether you measure output over the resistor or capacitor, and why. You do not need to choose values of R and C.
The ratio of the forward voltage to the forward current is called the characteristic impedance? What is forward voltage? What is the forward current? What is characteristic impedance?
b) Create a new folder name Lablb in your D:\Student_Matric_Number. Find the output X and show the simulation waveform. A B
(i) For the circuit below, draw the output waveforms for both the given input wave- forms. (ii) How can you convert this circuit into a half-bridge by removing any two compo- nents? Please draw a circuit diagram. Also, draw the current flow through the modified circuit. This can be done by annotating the modified circuit diagram. M (i) (ii)
V, = @sin(@t) + 2@ cos(@t). For this 6. A LRC circuit below is used to modify an input voltage applicatio, = 2 ydurāifidrentidi equation gnlist be in terms of %3D charge 9 notes to generate the general solution. No other method will be accepted. Use two decimal point accuracy. You . You must use the complimentary and particular solution method as shown in your are given that -2N@² + 20N = 2@ and -2M@² +20M = 2@¸ which you must use to simplify your particular solution when you equate coefficients. L HH Va VL Vc keo = Im sin(ot) Vs
.A series RLC circuit contains a 4-kN resistor, an inductor with an inductive reactance (X,) of 3.5 kn, and a capacitor with a capacitive reactance (Xc) of 2.4 kN. A 120-Vac, 60-Hz power source is connected to the circuit. How much voltage is dropped across the inductor?
: Answer All points: A d.c. circuit usually has .......... as the load Oresistance Oinductance Ocapacitance Oboth inductance and capacitance
Method: Transient AnalysisAn electronics hobbyist is working on a circuit that includes two capacitors, an inductor, and two resistors. The capacitors are C1 with a capacitance of 20 microfarads and C2 with a capacitance of 10 microfarads. The inductor, L1, has an inductance of 10 millihenries. The resistors are R1 with a resistance of 500 ohms and R2 with a resistance of 200 ohms. The voltage source provides 25 volts at a frequency of 1000 Hz. The hobbyist would like to know the current and voltage across each component in the circuit at 20 milliseconds and 100 milliseconds after the voltage source is turned on. Can you help the hobbyist determine these values?SHOW STEP BY STEP SOLUTION
The formula above should include a so-called sinc function (sinus cardinalis function).Use any available resource to find a formula that performs interpolation by means of the sinc function, and Explain why it can be useful to do sinc interpolation.
Explain the physical processes, that occur in RC and RL circuits when there are bursts of voltage being sent their way.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS