(b)Using the provided data:cross-section width w = 16 mm,cross-section hight h = 62 mm,length of the beam L = 3beam material's Young's modulus Q =228 GPa,applied bending moment MB = 12 kN.mThe value of the deflection at Point B caused by MB (Part I) can be calculated as●●●●●(c)mmm,Based on the given values of dimensions and material parameters,the value of R can be calculated askN;the value of the vertical reaction force at Support A can be calculated asthe value of the horizontal reaction force at Support A can be calculated asKNthe absolute value of the reaction moment at Support A can be calculated askN.mkN; Question 1A propped cantilever beam is loaded by a bending moment of the magnitude MB at thepoint B as shown in Figure Q1. The cross-section of the beam is a rectangle of thewidth w and the hight h that are constant along the length of the beam L. The beammaterial's Young's modulus is Q.XFigure Q1Assuming the positive deflections and positive vertical reaction forces are upward,calculateOthe value of the reaction forces at ints A and Bthe absolute value of the reaction bending moment at point A(a)Let R represent the reaction force at Support B. By releasing the beam at Support Band imposing a force R at Point B, the deflection of the beam consists of twoparts,i.e.Part I- the deflection caused by MB;Part II- the deflection caused by RPlease treat R, w, h, L, E as variables in this step, the mathematical equation forthe deflection at Point B caused by R (Part II) can be written as(Hint: to input equationR²LQwh you can type (R^2*L)/(Q^2*w*h))

Answered: Image /qna-images/answer/4aa88c42-401e-4b75-a401-ed031678c352.jpg

(b) Using the provided data: cross-section width w = 16 mm, cross-section hight h = 62 mm, length of the beam L = 3 m, beam material's Young's modulus Q =228 GPa, applied bending moment MB The value of the deflection at Point B caused by MB (Part 1) can be calculated as ● ● ● ● (c) mm = 12 kN.m Based on the given values of dimensions and material parameters, the value of R can be calculated as KN; the value of the vertical reaction force at Support A can be calculated as the value of the horizontal reaction force at Support A can be calculated as kN the absolute value of the reaction moment at Support A can be calculated as kN.m kN;

(b) Using the provided data: cross-section width w = 16 mm, cross-section hight h = 62 mm, length of the beam L = 3 m, beam material's Young's modulus Q =228 GPa, applied bending moment MB The value of the deflection at Point B caused by MB (Part 1) can be calculated as ● ● ● ● (c) mm = 12 kN.m Based on the given values of dimensions and material parameters, the value of R can be calculated as KN; the value of the vertical reaction force at Support A can be calculated as the value of the horizontal reaction force at Support A can be calculated as kN the absolute value of the reaction moment at Support A can be calculated as kN.m kN;

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.42P: For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending...

See similar textbooks

Similar questions

A propped cantilever beam is loaded by a bending moment of the magnitude M_B at the point B as shown in Figure Q1. The cross-section of the beam is a rectangle of the width w and the hight ℎ that are constant along the length of the beam L. The beam material’s Young’s modulus is Q. Assuming the positive deflections and positive vertical reaction forces are upward, calculate the value of the reaction forces at points A and B the absolute value of the reaction bending moment at point A A) Let R represent the reaction force at Support B. By releasing the beam at Support B and imposing a force R at Point B, the deflection of the beam consists of two parts,i.e. Part I- the deflection caused by M_B ; Part II- the deflection caused by R Please treat R, w, h , L , E as variables in this step , the mathematical equation for the deflection at Point B caused by R ( Part II) can be written as: b) Using the provided data: cross-section width w = 14 mm, cross-section hight h = 82…
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a-9 ft, b-6 ft and w=10.5 kips/ft. Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, -0, it has been omitted from the free-body diagram.) Answer: (a) Vi (b) V = i (c) V- a Answers: A, kips, Cy Determine the shear force acting at each of the following locations: (a) x = 0+ ft (i..., just to the right of support A) (b) x-9 ft (c)x=13ft When entering your answers, use the shear force sign convention. kips. kips. kips. b (a) M- (b) M- (c) M-i С Cy The shear-force diagram crosses the V = 0 axis between points A and B. Determine the location x where V = 0 kips. Answer:x-i ft. kip-ft. kip-ft. kip-ft. kips. Determine the maximum bending moment that acts anywhere in the beam. When entering your answer, use the bending moment sign convention.…
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=11 ft, b=6 ft and w = 12 kips/ft.Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)Answers: Ay = kips, Cy = kips.
For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 19.0 kips/ft, a=5.0 ft, and b=15.5 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. b Calculate the reaction forces By and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Bx = 0, it has been omitted from the free-body diagram.) a b By |C, Answers: By = i kips Cy = i kips Determine the shear force acting at each of the following locations: (a) x = 5.0- ft (i.e., just to the left of support B) (b) x = 5.0+ ft (i.e., just to the right of support B) (c) x = 19.5 ft (d) x = 20.5- ft (i.e., just to the left of support C) Note that x = 0 at point A. When entering your answers, use the…
A beam ABC rests on simple supports at points A and B and is supported by a cable at point C. The beam has total length 2L and supports a uniform load of intensity q. Prior to the application of the uniform load, there is no force in the cable nor is there any slack in the cable. When the uniform load is applied, the beam deflects downward at point Cand a tensile force I develops in the cable. Find the magnitude of this force. Cable A T A B C 000
6. Q1: For the beam Shown in Figure 1 (40 Points) 8kN/m 3kN/m 8kN/m 1. Find the reaction at support B RBy, the bending moment at B, and the bending moment at C. B- A 2. Draw the shear force and bending 3m 2m 2m 3m moment diagram for the beam. Figure 1 Q2: (30 Points) For the simply supported beam with loading and cross section shown in Figure 2, determine the following: 1. The location of the centroid measured 10 kN 10 kN 100 from the top fiber in (mm). 2. The moment of inertia about the 50 centroidal x axis (mm“) 3. The maximum compressive stress in 0.6m 0.6 m 0.6 m 30 30 60 30, (MPa) 4. The maximum shear stress at the neutral axis in (MPa) All cross-section 5. The average shear stress on the section dimensions in mm (MPа) If the allowable stress in tension, compression, and shear are 4 MPa, 18 MP, and 12 MPa respectively. is this Figure 2 beam safe?
Question 4 A beam made up of two unequal leg angles is subjected bending moment M having to a its vector at an angle 0 to the z axis as shown in Figure Q4 For the position shown, determine the onentation of the neutral axis 4.1 Calculate the maximum tensile stress and maximum compressive stress in the beam 4.2 Assume that 0 3.5 kNm 30° and M = 120 mmx80 mmx12 mm 120 mm 12 mm 80 mm Figure Q4
Learning Goal: To determine the support reactions in a statically indeterminate beam using the moment- area method. Part A - Support reaction force at B The beam shown has length L = 15.0 ft and is loaded with the applied moment M = 210 kip - ft at B. Assume EI is constant. (Figure 1) Using the moment-area method, determine the magnitude of the unknown support reaction at B due to the applied moment. Express your answer to three significant figures and include appropriate units. > View Available Hint(s) ? |By| = |10.5 kip Submit Previous Answers
Question 4 Sketch bending moment diagram for the loading acting on the beam as shown in Figure Q4. From your results, calculate area required for tensile reinforcement using M the formula 4, You may use fyk = 500 MPa and z = 1400 mm. 0.87 fyk 90 kN/m 30 kN/m 200 KN 20 kN/m Danim 100 kNm 2m 5m 3m Figure Q4
In Figure Q3a, a beam is supported at A and C with a uniformly distributed load of20 kN/m between A and B. Draw and label the shear force diagram (SFD) andbending moment diagram (BMD) for the beam shown in Figure Q3a. Label thevalues for shear force and bending moment at points A, B, C & at the beam midpoint M; the maximum bending moment and its distance from A; and clearlyindicate the type of bending between AB and between BC
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let w = 20.0 kips/ft, a=6.0 ft, and b=20.5 ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. y A A Answers: By a = Calculate the reaction forces By and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Bx = O, it has been omitted from the free-body diagram.) = a i B Cy i = W B b W b kips X kips X
PART 1 Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=2.0 m, PB = 2 kN, PC = 2 kN, and MB = 20 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. IMAGE* Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) IMAGE* PART 2 Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 3.5– m (i.e., just to the left of B)(c) x = 3.5+ m (i.e., just to the right of B)(d) x = 5.5– m (i.e., just to the left of C)When entering your answers, use the shear force sign convention.Answer:(a) V = ? kN.(b) V = ? kN.(c) V = ? kN.(d) V = ? kN. PART 3…