I need answer within 20 minutes please please with my best wishes Al Materials engineer needs to possess many skills during studying and job stage.knowledge and skills you attained through study the non-traditional machining of engineoringMaterials?B/Choose the correct answers for the following:1- Consider the following advantages offered by plasma are cutting:a- Heat affected zone is minimumb- Higher material removal rate is achieved.(c- All metals irrespective of their electrical conductivity can be cut.d- Narrower kerf is producedWhich of these advantages is true?2- Consider the following statements:a- AJM uses finer abrasive particles as compared to AWJM.b- Nitrogen and carbon dioxide are used to mix abrasive particles in AJM.c- It pruduces a uniform hole.d- AJM is used to cut softer materials,Which of these statements is true?3- Which of the following processes can be used to produce very small diameter holes?a- EDMb- ECMc- EBMd- WJM4- Consider the following parameters:a- Low metal removal rateb- Poor surface finish- iligh tooling costWhich of the above parameterstrue in the case of USM?5- Consider the following statements:a- Specific power consumption is very high.b- Processes are chipless.c- Close tolerances are difficult to achieve.d- Equipment cost is not very high.Which of the above statements is true in the case of non-conventional machining met

Plasma arc welding ***As per our company policy we are supposed to do only 1 question if you need…

B/Choose the correct answers for the following: 1- Consider the following advantages offered by plasma are cutting: a- Heat affected zone is minimum b- Higher material removal rate is achieved. All metals irrespective of their electrical conductivity can be cum d- Narrower kerf is produced

B/Choose the correct answers for the following: 1- Consider the following advantages offered by plasma are cutting: a- Heat affected zone is minimum b- Higher material removal rate is achieved. All metals irrespective of their electrical conductivity can be cum d- Narrower kerf is produced

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter1: Introduction To Welding

Section: Chapter Questions

Problem 18R: What cutting process uses a stiff, highly ionized, extremely hot column of gas to almost instantly...

See similar textbooks

Related questions

Q: 1. What is the working strength of a 2'' bolt which is screwed up tightly in a packed joint when the…

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: A steel shaft of diameter 50 mm and length 1.2 m is fixed at its ends A and B. If a 300 N∙m torque…

Q: The tape shown slides around two fixed pegs each of radius 30 mm as shown. If T1 = (0.1P in newton)…

Q: Figure 3. Borcon rocket set up. 4. Draw a diagram showing the momentum vectors of your balloon…

A: Given questions: 1.how do theses momenta compare? 2. How does the velocity of the air that is pushed…

Q: A 4ft hollow cylinder fixed at one end is subjected to a Load 1500lb at the other end perpendicular…

Q: Calculate the minimum wall thickness for a cylindrical vessel that is to carry a gas at a pressure…

A: following is the answer to the above problem-

Q: 1. (True / False) Stress components are opposite in direction on the two surfaces of an imaginary…

Q: 3 in I. Compute the centroidal distance with respect to x- and y- axis of the figures below. 4 in 6…

A: The centroidal distance with respect to x- and y-axis: X = 2.375 in ; Y = 3.25 in

Q: A centrifugal pump discharge 7500 L of water per minute against a total head of 25 m when running at…

Q: The specific gravity of a fuel oil is 0.803 at 15.60 C. What is its API rating? 3 decimal places

A: Given S.G of oil is 0.803 Find API rating

Q: helical compression spring having 14 active coils is close coiled. It has a spring stiffness of…

Q: Q.4 The condensing and evaporating temperatures of a standard vapor compression cycle using R134a…

Q: Part a) consider the system shown in Figure Q1a. Assume that the cantilever beam has length L, is…

A: For solution refer below images.

Q: Example 3 300 N 400 N P Q/ The figure above is in equilibrium find the value of the angle and find…

Q: A steel ball slides against an aluminum flat surface at two different normal loads. At low normal…

A: Given At low load Coefficient of friction = 0.4 Groove width, r = 0.4 mm At high load…

Q: 20-teeth sprocket driving a 100 teeth sprocket with a center distance of 38 pitches. Find the chain…

Q: 1. Draw the shear-force and bending-moment diagrams for the beam shown. Determine the maximum shear…

A: Draw the shear force and bending moment diagrams and find the maximum value of shear force and…

Q: The steel pipe is filled with concrete and subjected to a compressive force of 75 kN. Determine the…

Q: Water (cp=4180 J/kg K) is to be heated by hot air (cp= 1010 J/kg K) in a double pipe counter flow…

Q: Q1: A gas turbine power plant operating on an ideal Brayton cycle has a pressure ratio of 8. The gas…

A: given data T1 = 300 K T3 = 1300 K pressure ratio = 8

Q: A sports car travels along a straight road with an acceleration-deceleration described by the graph.…

Q: Q2/ A pipe with a radius of 15 mm is attached to a garden hose with a nozzle. If the velocity of…

Q: An insulated piston-cylinder device contains 3 L of saturated liquid water at a constant pressure of…

Q: A closed cylindrical tank contains 2.6m of water, 5.4m of oil (s=0.82) and the air above the oil has…

Q: The rotation or twist in degrees of a shaft, 800 mm long, subjected to a torque of 80 N-m, 20 in…

Q: m weight of 80N and rests against the wall at B.If the coefficient of 4, determine the smallest…

Q: In the double integration method by beams, the defection (y) equation where C2 represents _____…

A: The double integration method is a method that is used to solve or calculate the deflection and…

Q: Which of the following statements is/are true for deriving the relations between the bending moment…

Q: 6.18 Two uniformly distributed loads are placed symmetrically on the simply supported beam.…

A: we have to determine the value of maximum value of EI

Q: The air conditioner in a car uses R-134a and the compressor power input is 1.5 kW bringing the…

Q: The wall of an furnace consists of three materials having, k₁ = 20 W/m. K and kc = 50 W/m. K, and…

A: Thermal resistance is defined as the ratio of temperature difference to the heat flux. It has…

Q: Find the steady state response xss(t) KG) 4 HOkg Is liter TOFF 7 फल main m F(t) = 60SIN (40+) FIND…

Q: Topic: Centroid Graph and compute the center of mass/ centroid of the region R = {(x, y): 1 ≤ x ≤…

Q: Q5) Using a system similar to that shown in figure, compute the required air pressure above the…

A: Given data h1 = 0.3 mh2 = 5 mWe have to find the air pressure required to cause the jet to rise to…

Q: P: 400 N 300 M

Q: - A missile runs freely without of fuel in the location as shown in figure.2, calculate:- 1-…

Q: The compression ratio of an air-standard Otto cycle is 9.5. Prior to the isentropic compression…

Q: Find second moment of area Ixx about centroid, where b₁=14 mm, h₁=26 mm, b₂=5.8 mm and h₂ = 15 mm b2…

Q: A Look at the truss below. Fill in the correct magnitude with sign for each tension force acting on…

Q: Question 20 Calorimetry When determining the latent heat of fusion for ice, we added a small handful…

Q: Q6) The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure…

Q: 2. Draw the shear-force and bending-moment diagrams for the beam shown. Determine the maximum shear…

Q: undergo à constant pressure process until the quality becomes 50% (h₂ = 2220, V₂ = 0.075, S₂ =…

Q: A pipe of diameter 400 mm carries water at a velocity of 20 m/s.The pressure ta point A is 300000…

Q: 2. what is the reduction ratio, if D.-94mm, this means r=47mm=0.047m If pressure (P) = 45Mpa (45*106…

Q: Hand by written ans.Calculate the amount of dissolved oxygen in mg/L in river water at 30°C under…

A: Given, Temperature of the water = T = 30 oC Absolute value of temperature of water = Ta = 30 + 273…

Q: Q3/ Consider Steam is cooled from 550 to 111.4 °C. Assume that during this process the pressure…

A: GIVEN DATA- T1=550'C P1=300KPa T2=11.4'C P2=150KPa WE HAVE TO FIND ENTROPY CHANGE

Q: In an ammonia system one evaporator is to provide 180 kW of refrigeration at -30°C and another…

Q: Steam with a specific volume of 0.09596 m³/kg undergoes a constant pressure process at 1.7 MPa until…

Q: ILLUSTRATION AND SOLUTION Problem 1: A steel rod with a cross - sectional area of 150 mm2 is…

Concept explainers

Fire safety

Fire safety is a new domain emerged in the early 90s to enable the design of buildings, structures, and infrastructure against destruction through fire. It also includes the provisions of building codes. This field is mostly associated with the design and efficient planning of a building, to reduce the destruction caused by fire. The branch of engineering that deals with it for the safety of the buildings from destruction of fire, is known as fire safety engineering.

Question

I need answer within 20 minutes please please with my best wishes

Al Materials engineer needs to possess many skills during studying and job stage.
knowledge and skills you attained through study the non-traditional machining of engineoring
Materials?
B/Choose the correct answers for the following:
1- Consider the following advantages offered by plasma are cutting:
a- Heat affected zone is minimum
b- Higher material removal rate is achieved.
(c- All metals irrespective of their electrical conductivity can be cut.
d- Narrower kerf is produced
Which of these advantages is true?
2- Consider the following statements:
a- AJM uses finer abrasive particles as compared to AWJM.
b- Nitrogen and carbon dioxide are used to mix abrasive particles in AJM.
c- It pruduces a uniform hole.
d- AJM is used to cut softer materials,
Which of these statements is true?
3- Which of the following processes can be used to produce very small diameter holes?
a- EDM
b- ECM
c- EBM
d- WJM
4- Consider the following parameters:
a- Low metal removal rate
b- Poor surface finish
- iligh tooling cost
Which of the above parameters
true in the case of USM?
5- Consider the following statements:
a- Specific power consumption is very high.
b- Processes are chipless.
c- Close tolerances are difficult to achieve.
d- Equipment cost is not very high.
Which of the above statements is true in the case of non-conventional machining met

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

List the four common variations of the conventional plasma cutting process and describe the benefits of each.
What cutting process uses a stiff, highly ionized, extremely hot column of gas to almost instantly vaporizethe metal being cut?
Manufacuring Processes An electro chemical machining (ECM) operation is employed too cut a square hole in a copper plate of 18 mm thickness. The dimensions of the hole is 20 mm on each side, however, the electrode dimension shall be slightly less than 20 mm to allow for overcut, and its shape includes a hole in its center to permit the flow of electrolyte and reduce the area of cut. The frontal area of electrode is 180 mm2. The specific removal rate for copper is C = 7.35 x 10-2 mm3/A-s. The applied current is 950 A. At 90 % efficiency, determine the time required to cut a hole of required dimensions.
What cutting process uses a stiff, highly ionized, extremely hot column of gas to almost instantly vaporize the metal being cut?
7) Consider the following statements regarding Laser welding: 1: Conduction mode welding is normally used for welding thin sheets, whereas keyhole mode welding is used for much thicker sections. II: Vapour pressure from the hot metal helps to keep the keyhole open during keyhole mode laser welding. a. Statement I is correct, and statement II is incorrect. b. Statement Il is correct, and statement I is incorrect. c. Both statements I and Il are correct. d. Both statements I and Il are incorrect.
The frontal working area of the electrode in an Electrochemical Machining (ECM) operation is 1000 mm. The applied current is 900 amps and the voltage is 12 volts. The resistivity of the electi olyte is 140 Q-mm. The material being cut has a valency of 4 and specific removal rate of 0.0342 mm /A-s. If the process efficiency is 90%, determine the material remova! rate (MRR) and inter-electrode gap after 30 minutes of machining when the resistivity of the electrolyte has dropped to 75% of its original value.
5. What are the adverse effects of tool wear in cutting processes? 6. What characteristics are required for cutting tool materials? V. Comprehensive questions. 1. Match each part with the most proper manufacturing process. (1) Aluminum beverage can Centrifugal casting (2) Copper wire Closed-die forging (3) Engine cylinder Die casting (4) Lathe body Drawing (5) Link rod of an engine Sand casting (6) Magnesium alloy camera frame Sheet-metal forming
SHEET 5 Grinding, Welding and Galvanizing operations 1- Define Grinding process, what are the main characteristics of classification of a grinding wheel? 2- What are the main grinding operations, why coolant is uses in any cutting operation? 3- What are the main classes of welding? 4- With drawing explain flam different types, what type is used in cutting and why? 5- What are the differences between OXYACETYLENE and ARC welding? 6- What are the defects of ARC welding operation? 7- Explain the Electric Resistance Welding? 8- Define the GALVANIZING Process and what are the main governing parameters in this operation?
Outline wire electric discharge machining, its physics and applications?
8) Which one of the following statement is - not correct about ultra short pulse laser welding? a) Ultra fast b) Energy per pulse from nJ to mJ c) Average power varies from 10W to 1000W d) Pulse preparation frequency vary up to 100MHZ
Which of the following processes resulted in metallurgical damage to the cut surface: a. Ultrasonic machining b. Water jet cutting C. Plasma arc cutting d. Electrochemical machining e. None of them
Name two commonly used thermal cutting processes.