(c) Figure Q4(c)(i) shows the system consists of 1200 m of 5 cm cast-iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. Calculate gage pressure at point 1 to deliver 0.005 m3/s of water into the reservoir if elevation at point 1 is 400m. Given u = 0.001 kg/m s.; 450 long-radius elbow, k = 0.2; 90° long-radius elbow, k-0.3; Open flanged globe valve, k=8.5; submerged exit, k=1.0. [Please use: Moody Chart diagram in Figure Q4 (c)(ii) and attach it together with your answer script].

(c) Figure Q4(c)(i) shows the system consists of 1200 m of 5 cm cast-iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. Calculate gage pressure at point 1 to deliver 0.005 m3/s of water into the reservoir if elevation at point 1 is 400m. Given u = 0.001 kg/m s.; 450 long-radius elbow, k = 0.2; 90° long-radius elbow, k-0.3; Open flanged globe valve, k=8.5; submerged exit, k=1.0. [Please use: Moody Chart diagram in Figure Q4 (c)(ii) and attach it together with your answer script].

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Show the necessary figures (if applicable) 2.3) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Three pipes of 400 mm, 350 mm and 300 mm diameter are connected in series between two reservoirs with a difference in level of 12 m. The friction factors are 0.024, 0.021 and 0.019 respectively. The lengths are 200 m, 300 m and 250 m respectively. Which of the following statements is TRUE. * The discharge in pipe 1, 2 and 3 are decreasing. The total head loss is equal to the difference in elevation between reservoirs. The head loss in pipes 3 is equal to the sum of losses of pipes 2 and 3. The largest pipe will have the largest head loss The head loss in pipes 1, 2 and 3 are equal. * The flow in m^3/s in PIPE 3 is nearest to... 0.1 0.2 0.4 0.3 * What is the head loss in meters in pipe 3? 2.785 m 15.458 m 7.755 m 6.474 m Determine the length of an equivalent 350mm diameter pipe. * 402.582 m 906.123 m 1545.812 m 417.236 m
The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the tank is 0.028 m^3/ sec. Determine the minimum height, h, of the water tank under the assumption that (a) minor losses are negligible, (b) minor losses are not negligible. 3 m Figure No.3 Kentrance = 0.5 h The pipe is plastic of 15 cm diameter and (e/D=D0) 1.8 m (2) Main line 450 m with 15 elbows of 90 degree
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
2] A pipe discharges 130 lps of water into a reservoir at a point 1.85 m belowthe water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25m above the water surface. At the discharge end the pipe is 30.5 cm. If the head lossfrom A to the reservoir is 0.7 m, determine the pressure in A.
2. Consider the piping network shown. The pressure heads at points A and B are 80m and 52m, respectively. If the Hazen- Williams Coefficient for all pipes is 110, calculate the flowrate in each pipe. 1 A B 3 2 L₁ = 3000m L2 = 2600m L3 1300m D₁ = 300mm D₂ = 250mm D3 = 200mm
2. The suction pipe of a pump rises at a slope of 3 vertical in 4 along the pipe which is 12 cm in diameter. The pipe is 7.2 m long; its lower end being just below the water surface in the reservoir. For design reasons, it is desirable that pressure at inlet to the pump Pump 4/3 shall fall to more than 75 kPa below atmospheric pressure. Neglecting friction, determine the maximum discharge that the pump may deliver. Take atmospheric Suction pipe pressure as 101.32 kPa. F.W.S. Reservoir/sump 2. 7.2 m
Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section from point 1 to point 2, which is 1.5 m above point 1, at the rate of 0.9 m³/s. At section 1 the pipe dia is 0.5 m and pressure is 800 kpa. If pressure at section 2 is 600 kpa determine the pipe diameter at that location. (neglect the losses) tt thele loloses)
Q1: Three reservoirs connected by pipes. Each pipe has 300 mm diameter and 1500 m long. Assuming friction coefficient, f = 0.01. Find discharge in each pipe. B 2 D, L2 3 D,, L O D, L, 45 m 75 m D, = D, = D, = 300 mm L, = L, = L, = 1500 m 15 m C Datum
A pipe discharges 150liters/sec of water into a reservoir at a point 1.80m below the water surface. At point A the diameter is 250Omm and the center of the pipe is 1.20m above the water surface. At the discharge end of the pipe is 300mm in diameter. If the loss of head from A to the reservoir 0.65m, determine the pressure head at A A 1.2m 250mm water level 1.8m datum 300mm B
SITUATION 2: Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Elev 80 ha hez Elev 70 B 4000 m- 250 mm f-0.018 he 3500 m f- 0.018 Elev 60 Pipe 1: L= 5000 m, D = 300 mm Pipe 2: L= 4000 m, D = 250 mm Pipe 3: L= 3500 m 5000 m - 300 mm f= 0.018
ISTINYE ISU UNIVERSITY Question 2: A steel pipe is used to drain water from a reservoir that is 50 m above the datum, and water is discharged into the air at the elevation of the datum. The pipe is 1500 m long and 450 mm diameter and 50 mm wall thickness. A valve is installed at the downstream end of the pipe allows a flow rate of 0.71 m³/s. The valve was completely closed in 1.4 sec. Calculate maximum hammer pressure at the valve. The pipe is longitudinally anchored. Eb = 2.1×10° N/m², E. -1.9×10¹¹ N/m².