Clear solution and understandable handwriting please 1. Calculate the resistance of a 2 km length of aluminum overhead power cable if thecross-sectional area of the cable is 100mm². Take the resistivity of aluminum to be0.03 x 106 Q-m.2. For the circuit shown, find the Equivalent resistance, the value of supply voltage, thevalue of current I and the voltage drop at 60ohm resistor.2=3 AR2R1202R3= 60 N-10 Ω3. Find the current flowing and voltage drop at R,R1R230021002R3EsR41k2400 2300V

In this question we will find resistance of aluminum cable... Note :- due to bartleby policy , I…

Calculate the resistance of a 2 km length of aluminum overhead power cable if the cross-sectional area of the cable is 100mm?. Take the resistivity of aluminum to be 0.03 x 106 0-m. For the circuit shown, find the Equivalent resistance, the value of supply voltage, the value of current I and the voltage drop at 60ohm resistor. 2=3 A R R3 R2 60 0 ·20여 = 10 N

Calculate the resistance of a 2 km length of aluminum overhead power cable if the cross-sectional area of the cable is 100mm?. Take the resistivity of aluminum to be 0.03 x 106 0-m. For the circuit shown, find the Equivalent resistance, the value of supply voltage, the value of current I and the voltage drop at 60ohm resistor. 2=3 A R R3 R2 60 0 ·20여 = 10 N

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter17: Resistive-inductive Series Circuits

Section: Chapter Questions

Problem 1RQ: 1. What is the relationship of voltage and current (concerning phase angle) in a pure resistive...

See similar textbooks

Similar questions

1. What is the relationship of voltage and current (concerning phase angle) in a pure resistive circuit?
An ac resistance is higher than a dc resistance. True False
. Using the I – V curves how are ohmic materials different from non-ohmic materials
The resitance of a wire is 25 ohms at 50°C and 20 ohms at 30°C. Determine the temperature coefficient at 24°C. Note: DRAW THE DIAGRAM
The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence
An aluminum wire 7.5 m long is connected in parallel with a copper wire 6 m long. When a current of 5 A is passed through the combination it is found that the current in aluminum wire is 3 A. The diameter of aluminum wire is 1 mm. Determine the diameter of the copper wire. Resistivity of copper is 1.7 x 10 -6 ohm-cm and that of aluminum is 1.724 micro-ohm-cm.
W1 A 1 IL Tr1 AC Supply V V w2 12 Tr2 use double range voltmeter Fig.(1)
State the main constituent elements of electrical cables, as well as the materials from which they may be made. Describe the following designations: H05VV-U 1G4 mm? and LSXAV 3x16 mm?.
A 2 wire d.c. ring distributor is fed at A with 220 V. The various loads are 10A at B, 20A at C,30A at D and 10A at E. The resistances of the sections AB, BC, DC, DE and EA are 0.1 £2, 0.05 $2, 0.01 2, 0.025 2 and 0.075 respectively. Determine, a. Point of minimum potential b. Current in each section [Ans.: Point C, 29.04 A, 19.04 A, 0.96 A, 30.96 A and 40.96 A
Solve 2,3 only.Note the load resistance is 10 ohm and frequency 60 Hz
10) A certain batch of copper wire was found to have a conductivity of 98% at 20°C. What is its resistivity in un-cm? www
use these two images to answer all these questions: What are the differences between ac and dc meters? Can you compare the value of the current in the load resistance for the same value of voltage with ac and dc supply? What is the function of the autotransformer in this circuit? Can you use an autotransformer to obtain variable output voltage from a fixed dc supply? What will happen if dc meters are used instead of ac meters in this circuit? What the difference between resistance and impedance is when referred to dc and ac measurements?