Calculation: Compressive Strength (CS) = P/A Where: CS = compressive strength of the specimen, psi (KN/m²) P = maximum load, Ib (KN) A = cross-sectional area of the specimen, inches (m²) Gross Area: Tabulated Data and Result Trial No. b (m) w (m) A (m²) P (kN) CS (kN/m²) 1 0.4 0.15 0.06 150 2 0.4 0.15 0.06 180 0.4 0.15 0.06 140 Net Area: Tabulated Data and Result Trial No. A (m²) P (kN) CS (kN/m²) 1 0.0296 150 0.0296 180 3 0.0296 140

Calculation: Compressive Strength (CS) = P/A Where: CS = compressive strength of the specimen, psi (KN/m²) P = maximum load, Ib (KN) A = cross-sectional area of the specimen, inches (m²) Gross Area: Tabulated Data and Result Trial No. b (m) w (m) A (m²) P (kN) CS (kN/m²) 1 0.4 0.15 0.06 150 2 0.4 0.15 0.06 180 0.4 0.15 0.06 140 Net Area: Tabulated Data and Result Trial No. A (m²) P (kN) CS (kN/m²) 1 0.0296 150 0.0296 180 3 0.0296 140

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

A compact tension specimen is tested according to ASTM standard E399. The load displacement curve is shown in the Figure below with PQ= 120 kN (Type 1 curve). The specimen dimensions are B=0.5 cm, W=10 cm, and “a” =5 cm. If the materials yield stress is 600 MPa are the conditions correct for a valid K1C measurement? Please look up McEviley’s textbook on the thickness criterion for a valid fracture toughness value.
Two 150 mm * 300 mm concrete cylinders with randomly oriented steelfiber contents of 0 and 2% by weight, respectively. After curing for 28 days,the specimens were subjected to increments of compressive loads until failure. The load versus deformation results were as shown in Table P7.45. Assuming that the gauge length is the whole specimen height, determine the following:a. The compressive stresses and strains for each specimen at each loadincrement.b. Plot stresses versus strains for the two specimens on one graph.c. The initial modulus of elasticity for each specimen.d. The ultimate strength for each specimen.e. The strain at failure for each specimen.f. Toughness. Curves may be approximated with a series of straight lines.g. Comment on the effect of adding fiber on the following:i. Modulus of elasticityii. Ultimate strengthiii. Ductilityiv. Toughness
A tensile test was carried out on a metal specimen. The gauge length of the specimen was 96 mm and the initial (original) cross sectional area was 17.36 mm^2. The final (fractured) length was 107.4 mm and the final cross- sectional area was 16.40mm^2 . Determine the percentage elongation and percentage reduction in area of the specimen.
Procedure: 1. Compression tests on specimens shall be made as soon as practicable after removal from the moist storage. A 28-day test shall be performed within +-20 hours of the 28thday. Test specimens shall be kept moist by any convenient method during the period between removals from moist storage and testing. They shall be tested in moist condition. 2. All test specimens for a given test age shall be broken within the permissible time tolerance prescribed below. TEST AGE PERMISSIBLE TOLERANCE 24 HOURS +-0.5 HOURS OR 2.1% 3 DAYS 2 HOURS OR 2.8% 7 DAYS 6 HOURS OR 3.6% 28 DAYS 20 HOURS OR 3.0% 90 DAYS 2 DAYS OR 2.2 % 3. With a clean rag or rush clean the bearing faces of the bearing blocks, test the specimens and exclusion controller (elastomeric cps). 4. Rest the specimen on the lower extrusion controller, place the top extrusion controller on the specimen, and check the spacing between the sides of the specimen and the extrusion controllers to ensure no contact between the cylinder…
I. Problem Solving: Answer what is being required. Show you complete solution. 1. Compute the flexural stress of the sample specimen if its dimension is 150mm x 150mm x 500mm in a 3 point loading. The effective length is 400mm. The specimen failed at 44,300N in the middle third. 2. Compression test was applied to a certain type of wood. Compute the stress based on the following dimensions. The grains are parallel with the length. а. Compression Test Dimension (mm) Load (N) Compressive stress (MPа)
I. Problem Solving: Answer what is being required. Show you complete solution. 1. Compute the compressive stress for the respective ages of the specimen. The diameter of the specimens is 150mm and the height is 300mm. Load (N) 176,000 Stress (MPa) Age 7days 14 days 28 days 252,000 340,000 2. Compute the tensile stress from the value acquired from the experiment if the breaking load is 105KN. The diameter of the specimen is 150mm and the height is 300mm. 3. Compute the flexural stress of the sample specimen if its dimension is 150mm x 150mm x 500mm in a 3 point loading. The effective length is 400mm. The specimen failed at 44,300N in the middle third. 4. Compression test was applied to a certain type of wood. Compute the stress based on the following dimensions. The grains are parallel with the length. а. Dimension (mm) Load (N) Compressive stress (МРа) Compression Test
Calculation: For center Loading: MR = 3PL / 2bd? Where: MR- modulus of rupture, psi (MPa) P= maximum load applied as indicated by testing machine, in Ib (N) L= span length, in inches (mm) b= average width of specimen in inches (mm) d= average depth of specimen, at the fracture, in inches (mm) Note: The weight of the beam is not included in the above calculation. Tabulated Data and Result Sample No. L (mm) B (mm) D (mm) P (N) MR (MPa) 1 450 150 150 23000 2 450 150 150 21000 3 450 150 150 19000
What is unconfined compressive strength test, which triaxial compression test is similar to shows? If the maximum compressive stress value obtained from this test is qu, this test Show the shear strength of the specimen using the Mohr tensile circle. Also, short Why is the unconfined compressive strength of the Comment on its use. I will understand better if you type the answers with the keyboard thank you.
A cylindrical brass specimen having a diameter of 1.10 cm and initial gage length of 4.04 cm is subjected to tensile strength test. The load-deformation values are given in the below table. The final length and final diameter of the specimen were measured as 4.33 cm and 0.92 cm, respectively. Complete the below table and plot true stress-true strain diagram and determine. Yield strength at 0.2 % off-set method. Poisson’s ratio of the material at 135 kN load (assume that there is no volume change) If the material were unloaded from 175 kN, what would be its final length? 1 nm=1*10-9 m, 1 0A=10-10 m
S1:Q1 a) Figure 1a provides dimensions of a test sample that is being subjected to a tensile stress. If the stress at section Y-Y is 188N/mm2 and the force is 220 kN, calculate the dimension X. Y 1.8cm- Y Not to scale Figure 1a
The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. The inset shows a detailed view of the curve at low strains. 400 350 300 250 Stress (MPa) 200 150 100 50 0 0.00 Stress (MPa) 350 kN 300 250 200 150 100 50 0 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 Strain 0.18 What is the maximum force that could be applied to the specimen before it plastically deforms?
Situation 3 A compressive strength test were conducted to the following cylinder; Cylinder 1 3015 psi Cylinder 2 2950 psi Cylinder 3 3253 psi Cylinder 4 3004 psi Cylinder 5 3031 psi It is observed that the size of the cylinder is 6% in x 12" which is much bigger that the standard cylinder specimen. 1. What would be the reported compressive strength for each cylinder. 2. What is the average compressive strength? 3. If the target compressive strength at: 3 days is 3000 psi, What can you say about the test result?