Define the functions of cap block, drive cap and pile cushion in driven piles?
Q: interior column loads are 500 tons and pile groups are not to exceed eight, determine the cross-…
A:
Q: he soil profile and soil properties at a site are shown in the table below. A group of 12 concrete…
A: Given data : Number of Piles : 12 3 x 4 matrix L = 12m D = 0.45m Pile spacing 1.5m S = 3D =…
Q: . What is pile foundation? Discuss the classification of pile based on materials/composition and…
A: Deep footing - If the depth is more, the footing are considered as deep footings. Meyerhoff (1951)…
Q: Explain the difference between short piles and long piles.
A: Short pile : - Short pile are generally 2m to 4m and from 250 mm to 350mm diameter. - The piles may…
Q: Why would it be inappropriate to use the Terzaghi bearing capacity formulas to determine the toe…
A: The ultimate load which a foundation can support is calculated by terzaghi bearing capacity…
Q: Provide Feld’s rule for determining group capacity of pile groups ?
A: The general mathematical formula to calculate the efficiency of the pile group is ζ = Total pile…
Q: Describe the important advantages of driven piles.
A: Piles are defined as a foundation that provides support for the building structure. it is used for…
Q: Q # 1. What is pile foundation? Discuss the classification of pile based on materials/composition…
A: Pile foundation- a foundation laid with deep pile is known as pile foundation.
Q: Define the Types of piles and their functions ?
A: The different types of piles are: 1.End bearing 2.Friction piles 3.Friction and cohesion pile
Q: Question 73/75 Static axial compressive pile load test shall be in accordance with what standard?…
A: Static axial compressive pile load test shall be in accordance with what standard? The answer is…
Q: Explain why pile driving formulas are not reliable, and why a wave equation analysis is a better…
A: Solution: Pile driving formulas are not reliable because Pile Driving formulas are very simple.…
Q: Explain some conditions which are consider for the structural design of driven piles.
A: The driven pile may be a form of pile that inserted up to the exhausting layer within the soil…
Q: State the different types of piles according to its function and construction?
A: The types of piles are:End bearing piles: These pile have strong ends so as to resists the load and…
Q: Discuss the following method of load carrying capacity of pile : Static formula
A: There are four types of the load-carrying capacity of piles1) Static Method2) Dynamic Formulas3)…
Q: Which one is a better choice, a large diameter piles or a system of several smallerpiles with the…
A: Piles plays pivotal role in stabilizing the superstructure. These are embedded vertically down into…
Q: In piling works, normally founding levels of bored piles are defined by using total core recovery or…
A: Piling is defined as being foundations that are driven or bored through the ground along a certain…
Q: A circular pile having a diameter of 0.44 m is 16.41 m long which is embedded in a layer of dense…
A:
Q: A 3 x 3 pile group with pile spacing of 1 m and pile diameter of 0.40 m supports a load of 3 MN.…
A: The load on the pile is P=3 MN. The void ratio is e=0.65. The coefficient of consolidation is…
Q: c) Pile foundation design to Eurocode 7 offers a method of design using pile testing data, and an…
A: concept- Pile foundation- The base of the pile is a set of columns erected or laid out to transport…
Q: The length of friction piles based on O Shear strength of soil O Pile size O applied load O all of…
A: 6. The length of friction piles based on: The loads are transferred from the structure to the soil.
Q: Discuss the following method of load carrying capacity of pile : Dynamic formula
A: Dynamic formulas are as follows. Engineering News Formula Hiley's Formula
Q: What distinguishes displacement piles from nondisplacement piles?
A: When the depth of a base exceeds three times the width, it is said to be stacked. A powered pile is…
Q: Q2/What are the Classification of Piles According to Method of Construction?
A: The given question is based on foundation engineering.
Q: A group of 9 piles of 27 cm diameter is arranged in a square configuration with a center-to-center…
A: Given data in question Cohesion Adhesion factor Square pile Spacing Length To find out Ultimate…
Q: What are Compression piles ? Explain the purpose & uses of Compression piles ?
A: Compression Pile :These are the piles that are acted upon by compression loads and they carry the…
Q: 1. What types of piles you know by their bearing mechanism
A: The various types of piles are: Sheet piles: This type of pile is mostly used to provide lateral…
Q: An anchored sheet pile is to support a mass of cohesionless soil up to a height of 6 m above ground…
A: Given Unit weight of soil=21 KN/m3 Angle of internal friction= 30°
Q: Discuss about the Carrying capacity of single pile in granular and cohesive soil ?
A: The load bearing capacity of foundation soil or rock which enables it to bear and transmit load…
Q: Discuss the method of obtaining ultimate load and also allowableload on a single pile from pile load…
A: Pile load test is the in situ method of the calculation of the load and settlement. This method is…
Q: Describe the factors of safety for design of piles.
A: Answer IntroductionA pile foundation is a cylindrical structural member made of concrete, steel, and…
Q: For a rigid pile cap with vertical piles at the middle and raking piles at the sides,what is the…
A: Brief concept- Piles are provided in the deep foundation where the applied load is very high and the…
Q: Describe about the Relation between pile capacity and driving.
A: The soil that surrounds a pile is substantially disturbed when pile is driven in normally to lightly…
Q: What are the primary advantages of using laterally loaded vertical piles instead of battered piles?
A: Introduction: Piles are used generally to transmit vertical loads and lateral loads to the…
Q: Structural designers commonly mention that steel piles are a good choice for sites where long piles…
A: Steel pile and concrete pile don't seem to be interchangeable solutions for foundation repair. every…
Q: Please help me solve The soil profile and soil properties at a site are shown in the table below.…
A: Given data Number of Piles =12 n a 3 x 4 matrix L = 12m D = 0.45m Pile spacing 1.5m
Q: Answer the following 1-Point bearing piles extend to a stable soil or rock layer below the…
A:
Q: Explain how wave equation analysis combined with static or dynamic load tests can be used to…
A: The wave analysis process is very important to know the relation between the pile capacities and…
Q: A proposed highway bridge will be supported by 180 piles, each about 18 m long. The design load per…
A: Number of piles required for pile load tests varies from 0.5% to 2% of the total piles of the…
Q: 4. The following data was obtained in a vertical pile load test on 300 mm pile diameter pile.…
A: Safe load / Allowable load on a single pile should be the least of the following: 1 Two-thirds of…
Q: What s pile foundation? Discuss the classification of pile ba =/composition and load transfer…
A: Pile foundation- Plie foundation is a type of Deep foundation where depth of foundation is grater…
Q: 8. Pile Capacity Calculations A 30" diameter friction pile which has a 24' length in contact with…
A:
Q: What is pile foundation? Discuss the classification of pile based on materials/composition and load…
A: Pile Foundation - Pile foundation is type of deep foundation which is used to transfer the building…
Q: Describe the pile model used in wave equation analyses with the diagram.
A: Proper modeling of pile driving is important for both planning and inspection of pile driving…
Q: 2. A 40 cm diameter pile carries an allowable load of 200 kN with unit weight of 19 kN/m3 and…
A:
Q: An engineer is designing a deep foundation at a site underlain with loose to medium dense sandy silt…
A: The long circular section which is made up of hard material to carry loads and transfer it to hard…
Q: 5. Discuss five advantages of using large diameter bored piles compared to driven steel H-piles for…
A: These type of piles is used mostly in the construction process. Because it is having many advantages…
Q: Why would it be inappropriate to design a drilled shaft using a static analysis method developed for…
A: Static analysis is used to figure out: A pile's or a pile collective's nominal resistance in…
Q: A helical pile with 12 in diameter flights and a 2 in square rod is to be installed to a depth of 30…
A: Given:- The diameter of the helical pile = 12 in The thickness of the square rod = 2 in The depth…
Q: A 30 cm diameter concrete pile is driven into a homogeneous consolidated clay deposit (Cy = 40 kPa,…
A:
Define the functions of cap block, drive cap and pile cushion in driven piles?
Step by step
Solved in 2 steps
- Describe the factors of safety for design of piles.Explain the difference between a rigid analysis and a nonrigid analysis for lateral pile loading. Think about soil-structure interaction.describe the procedure that is required to design a pile foundation and why would it be used. What is the required information to design these piles