Determine of the internal resistance force of each segment of the bar shown below, and the total elongation of the bar. Let: The forces acting P₁=150kN, P₂=250kN, P3-200kN, P4-50kN. Areas of the bar segments A1=1000mm, A2=2000mm, A3=1000mm. E=200Gpa -2000 mm -1000 1500 IP₂ lb P3| PA a a A₁ B A₂ A3 IC C D

Determine of the internal resistance force of each segment of the bar shown below, and the total elongation of the bar. Let: The forces acting P₁=150kN, P₂=250kN, P3-200kN, P4-50kN. Areas of the bar segments A1=1000mm, A2=2000mm, A3=1000mm. E=200Gpa -2000 mm -1000 1500 IP₂ lb P3| PA a a A₁ B A₂ A3 IC C D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.11.4P: A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material...

See similar textbooks

Similar questions

A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material of the bar has the stress-strain curve shown in the figure. Determi ne t he elongation 5 of the bar for each of the following axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN. and 45 kN. From these results, plot a diagram of load P versus elongation 5 (load-displacement diagram).
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
Determine of the internal resistance force of each segment of the bar shown below, and the total elongation of the bar. Let: The forces acting P₁=150kN, P₂=250kN, P3=200kN, P4=50KN. Areas of the bar segments A1=1000mm, A2=2000mm, A3=1000mm. E=200Gpa -2000 mm -1000- ** -1500 P₂ 1b P3 P4 P₁ A₁ la a B A₂ b C A3 C C D
Q/1: (20 Marks) A brass bar having a cross sectional area of 500 mm2 is subjected to an axial force as shown in the figure. Determine the total elongation of the bar. Take E=80 GPa. В 100 kN 80 kN 50 kN - 30 kN 500 mm 1000 mm 1200 mm-
Let's consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.995 mm. determine the applied force F. Select one: O F=15708N O F= 10472 N O F=5236 N O F= 13090 N O F=6283 N O F=4189 N
( 48ll O O 2 9:YV The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230 GPa has an outer diameter 37 mm and wall thickness of 7 mm. If T1=803 N.m and T2=1445 N.m, answer the following questions: A B T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: F = 10472 N O F = 6283N O F= 15708 N O F = 4189N O F = 5236 N O F = 13090 N Clear my choice
Four axial forces are applied to the 25mm thick structural steel bar with 40mm diameter pins as shown in figure below. If the maximum allowable tensile stress in the bar is 135MPA and the maximum allowable deformation (extension or contraction) of the bar is 1.25mm, determine the minimum width, w of the bar. E - 200GPA. 270KN 90KN 220kN BỌ DO t= 25mm w=? 250mm 500mm 750mm Solution: [Ans : Wmin =65.2mm pon