determine the developed stresses, the changes in length, and the changes in diameter forsuch that the total change in length is (0.6 mm). Using (E= 190 GPa) and (G= 72 GPa),QuestionsQ1: The bar (ABC) has a circular cross section and is subjected to an axial tensile forcethe part (AB) and (BC).B.15mm20mm500mm750m

Answered: Image /qna-images/answer/148f83ef-484b-414b-8dfb-c17151757999.jpg

determine the developed stresses, the changes in length, and the changes in diameter for QI: The bar (ABC) has a circular cross section and is subjected to an axial tensile force such that the total change in length is (0.6 mm). Using (E= 190 GPa) and (G= 72 GPa), Questio is the part (AB) and (BC). 15mm 20mm 500mm 750m

determine the developed stresses, the changes in length, and the changes in diameter for QI: The bar (ABC) has a circular cross section and is subjected to an axial tensile force such that the total change in length is (0.6 mm). Using (E= 190 GPa) and (G= 72 GPa), Questio is the part (AB) and (BC). 15mm 20mm 500mm 750m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Similar questions

-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
A piston-cylinder has a force F₁ applied to it. The circumferential stress in the cylinder cannot exceed Omax = 6 MPa. Hint: 1. Pressure = F Area P = F₁ F₁- OG Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value T'inner 44 mm t 1.25 mm r1 a. Determine the max pressure that the piston-cylinder can withstand, P. b. Determine the magnitude of max force that can be exerted on the piston to not exceed omax, F1. kPa N
200 mm diameter rod is subjected to loads as shown. Determine the state of stress at points A and B. Show your results on an infinitesimally small square plane (please use the ones drawn below, which helps you in directions). 8 m 600 N 10 m 400 N 700 N + Oz Tyz + Txy Ox Oy A
Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses at point B on the shown cross-section. (b) Show the state of stress at the point B on a volume element. 400 lb B 1 in. 2 in. 500 Ib 2 in 10 in. 1.5 in. 1.5 in. Show your steps and highlight the following answers please I =
Calculate the combined stress (MPa) on the rod shown below using the principle stress method. Here, F1 = 0.35 kN, F2 = 0.12 kN, T = 428000 N-mm. Length and diameter of the rod are 75 cm and 75 mm, respectively. F2 F1 d
3. An axial pull of 35000 N is acting on a bar consisting of three lengths as shown below. If the Young's Modulus is 2.1 x 105 N/mm2. Determine (i) Stresses in each section, and; (ii) Total extension of the bar. Section 3 Section 2 Section 1 35000 N 35000 N 2 cm DIA 3 cm DIA 5 cm DIA k-20 cm- 25 cm -22 cm-
Two brass rods AB and BC, each of uniform diameter, will be brazed together at B to form a nonuniform rod of total length 100 m, which will be suspended from a support at A as shown. The density of brass is 8470 kg/m^3 Determine normal stresses of ((σzz)AB and (σzz)BC) as a function of z, and draw the variation of stresses with respect to z-axis on the same graph.
In this figure is a strut and a cable which was used to lift a body, if the strut and a cable has a stress equivalent to your SN and MN in kips respectively, determine the maximum weight of that body. Neglect the weight of wood and cable. Note: Round off your answer in two decimal places. ... Cable (A = 0.5 in 2) 9 ft C B 12 ft Weight A Wood Strut ( A 16 in 2)
(1) Given: b₁ B P=28 kN Square Bars b₁ = 57 mm (2) Q =9 kN b2 C b₂ = 19mm (3) Q R = 38kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.
Determine the compressive force (in Ib) in the bars shown after a temperature rise of 149°F if d = 0.012 in. Round off the final answer to five decimal places. d ... L M Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.73 sq. in E = 14930924 psi L = 13.4 in E = 10543748 psi L= 16 in a = 11.76 x 10-6/ °F a = 12.54 x 10-6/°F