Each of the links AB and CD is made of aluminum and has a cross-sectional area of 0.15 sq.in. Knowing that they support the rigid member BC, determine the downward deflection (in inches) of point E. if x = 13.5 in, y = 23.6 in, z = 20 in, E = %3D 10818755 psi, and P = 42 kips. Round off the final answer to five decimal places. A D

Each of the links AB and CD is made of aluminum and has a cross-sectional area of 0.15 sq.in. Knowing that they support the rigid member BC, determine the downward deflection (in inches) of point E. if x = 13.5 in, y = 23.6 in, z = 20 in, E = %3D 10818755 psi, and P = 42 kips. Round off the final answer to five decimal places. A D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

回の at D ana Pa at all 400 MPa of 3.0 is 4.0 m рe aplied nd the pin Q9. Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. Knowing that the magnitude of P is 4 kN, determiñe (a) the value of Q so that the deflection at A is zero, (b) the corresponding deflection of B. 20-mm diameter 0.4 m 0.5 m 60-mm diameter 2.
ht nces Required Information Portion BC of the rod ABC are made of an aluminum for which E= 70 GPa and portion AB is made of steel for which E= 200 GPa. Given: P = 8 kN, a = 0.9 m, b=1 m and the diameter of rod AB is c = 38 mm, (a) Determine the value of Q so that the deflection at A is zero (b) The corresponding deflection of point B 60-mm diameter Assume Q Is In (KN). Using the FBD/equilibriums equations of ABC and/or cut section between A&B and/or cut section between B&C, (1) The Internal axial force between A&B can be written as PAB= (KN) (T) -Q) (KN) (T) (11) The Internal axial force between B&C can be written as PBC=(
Links BC and DE are both made of steel (E = 29 x 106psi) and are 1/2in wide and 1/4in thick. Determine the corresponding deflection of point A if P = “W +X” kips
Use slope-deflection method to compute the bending moments of element ends for the following structures: 7) Use slope -defle ction Ast 4 4 12 t- 2006 Pa I= 100x 16mm" E = 200 GPa %3D I= 100× 106 mm4 For this question also compute the deflection at Point B.
For the truss shown in Figure 2: (Take, A 30 mm and E= 200 Gpa for all members) 1 Find the horizontal deflection at joint D, 2 Find the vertical deflection at joint F. 3 If member BF is 5 mm short (fabrication error). Find the horizontal deflection at joint D. 15 kN 15 kN 1.0 -20 kN -20 kN -0.556 -25 kN 1.12 0.556 3. 0444 0444 B 25 kN C 11.25 kN 11.25 kN A= 30 mm E= 200 X 10 kN/m (all members) 4 m 4 m 4 m Figure 2
Compute the deformation of the beam using area method:E= 200 GPa I= 1000 x 106 mm4
Rigid member ABCD shown here is used to support a 2 KN weight. This member is 6-m-long. Steel (E = 200 GPa) rods BE and CF have a diameter of 0.5 cm and length of 2 m. What is the deflection of point d when the weight is applied? F Multiple Choice O 2.92 mm 1.84 mm 2.31 mm 3.76 mm +x+w
A steel beam is subjected to a uniform load with length of 8m. Assume that the beam is simply supported. Use Fy= 248 Mpa. Properties of W-shape beam d=229 mm bf=210 mm rf=23.7 mm Tu-14.50 mm kdes=33. 80mm ry=53.80 mm Ix=113 x 10^6 mm^4 Iy-36.9 x 10^6 mm^4 Sx-990 x 10^3 mm^3 Zx 1150 x 10^3 mm^3 J-2100 x 10^3 mm^4 Cu-387 x 10^9 mm^6 What is the nominal shear strength capacity of the section (in kN)?
Determine the smallest cross-sectional area A for the members of the truss shown in Figure 2, so that the vertical deflection at joint B does not exceed 0.4 inches. Use the method of virtual work. EA = constant E = 1,600 ksi Figure 2: 10 k D A - 20 k E B 2 at 6 ft 12 ft EA = constant E = 1,600 ksi www. ARCHES AGAKHISKONSTMETE 10 k F AC 3 ft
Rigid member ABCD shown here is used to support a 2 kN weight. This member is 6-m-long. Steel (E = 200 GPa) rods BE and CF have a diameter of 0.5 cm and length of 2 m. What is the deflection of point d when the weight is applied? (A) 4.6 mm (B) 2.3 mm (C) 3.8 mm (D) 5.5 mm +x-w
Problem. The truss shown in Figure 1 is made from seven members, each having a mass per unit length of 9 kg/m. determine the distance d (x) to where the lifting cole must be attached, so that the truss does not tip (otate) when it is lifted. Ignore the mass of the gusset plates at the joints and the thickness of the members can be neglected. 6m B Y A www 6m ~8-5m C 37 6m Figure 1 For Problem D
365 For a 200 mm x 200 mm beam shown below with E = 20 GPa, select in the choices %3D the value that most nearly gives the following; Use Conjugate Beam Method 25.50 Reaction at D in kN [ Select ] Deflection at B in mm [ Select ] Deflection at C in mm 19 kN/m 5 kN/m BI 4.2 m 3 m - -3.6 m B & C are int. hinge %23 to search acer