Answered: equivalent circle. (b) Compare the line…

equivalent circle. (b) Compare the line of actions, as well. The initial wide triangular gate is shown in the figure below.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A homogeneous rod of constant cross section has length of 6 m and weighs 2500 N. The rod is resting…

A: Objective: To determine the reactions on the floor and wall, and the tension in cable CD. Given:…

Q: 1. Draw the shear and moment diagram 40k A 5 k/ft B

A: Given : Determine the shear and moment diagram ?

Q: 3. The upper and lower stadia hair readings on a stadia rod held at station B were observed as 4.50m…

A: S3 = 4.50m S1 = 1.35m K = 99.75 Height of instrument above A = 1.52m S2 = 2.5m θ = 25°15' To…

Q: A cantilever beam has a span of A m. and having a flexural rigidity of 40000 kN.m2. At the free end…

Q: Complete the table below. LINE BEARING DIST (M) AB N 68° 11.9' E 53.852 BC S 45° 0' E 28.284 CD S…

A: Answer Let us first calculate the latitude and departure of given lines To calculate the Latitude…

Q: S 45 deg E is converted to an azimuth of A 135 B 125 115 145

A: The given bearing is in terms of Quadrantal bearing. Azimuth is the angle subtended with North in…

Q: Calculate the number of bags required in the baghouse to dean the airstream, which is flowing at…

A: Solution- Area of baghouse required is 100,000 ft3/min3ft/min equals 33,333 ft2

Q: Use Double Integration Method in finding for the deflection at midspan. 5M 60 KN 50 KN T. ZT. 60° A…

A: To determine - Deflection at the mid span using double integration method.

Q: 3. The tension member is fastened together using a single bolt as shown. The bolt has a diameter of…

A: Given : Dia of bolt = 0.6 in. Allowable shear stress for bolts = 8ksi Allowable average normal…

Q: A cable supported at points A and B 210m horizontally apart with B 30m higher than A. The cable sags…

Q: DETERMINE THE CENTROIDAL MOMENT OF INERTIA X PL 10 X 1/2 [254 X 12.7 mm] W 10 X 26 -X

Q: A GO 10 LBS GO 8 35 42.5 77.5 C D 70 E h 22888886 AC JOINT D ONLY 8888 BD CD X DE X Y Y LOAD TOR C

A: Solution: Assume all the members are in tension. A positive sign (+) indicates the member is in…

Q: Solve for the reaction at B and E.

Q: Convert a forward azimuth of 180°-00'-01" to its equivalent forward bearing S 000-00¹-59" W OS…

A: Objective: To convert the given forward azimuth to its equivalent forward bearing. Given:…

Q: *4-4. Determine the moment about point A of each of the three forces acting on the beam. A F₁ = 375…

A: When a force is acting about a point or axis, the size of the moment is exactly proportional to the…

Q: Fig. 2. Assume constar factors, with f = 0.018. The head-discharge relation for the pump is Hp =…

Q: The value of M in the beam ABC shown in the figure is such that the joint B does not rotate. 30 kN/m…

A: Given data- Beam ABC with shown load is given. To Find- The value of support reaction at B.

Q: Situation: A bicycle tire is inflated with air. The density of the air in the inflated tire is 0.4…

Q: How to apply grip editing in AutoCAD?

Q: A saturated 100 cm³ clay sample has a natural water content of 30%. It is found that the shrinkage…

Q: Determine the coordinates of the centroid of the lines shown with respect to the indicated X and Y…

A: Given, A section,

Q: Determine the coordinates of the centroid of the lines used as boundaries of the ea shown in Problem…

Q: The infinite sand slope shown in the figure is on theverge of sliding failure. The ground water…

A: Given data- Infinite sand slope- Unit weight of water- γw=9.81 kN/m3, Saturated unit weight- γsat=21…

Q: Compute the latitude for the following line: S 22°-15'-48" E 140.58 O-58.0142 O-58.2607 O-130.1001 -…

A: Objective: To compute the latitude for the given line. Given: Bearing=S 22°-15'-48'' E…

Q: The time for 50% consolidation of a 1-in. thick clay layer (drained at top and bot- tom) in the…

A: To find time required to consolidate 8ft layer

Q: rotating the area through

Q: What is the calculated wastewater flow in CFS through a Parshall flume with a throat width of 10.0…

A: Given data:- The given throat width is 10 feet. The given maximum flow head is 4.5 feet. Use…

Q: Problem no. 1. Compute the reaction forces at pt. A and B D C A 9 m B 3m 1.5 m 3m 30° 20 KN

Q: der at the Lemieux Island WTP breaks down. As sho flows into a 5 km long distribution pipe. The…

A: Solution- No. of people = 190,000 volume used by each people = 200 litre/day discharge = Q=…

Q: The following are the data obtained in a stream gauging operation. A current meter with a…

A: Given details obtained in a stream gauging operation V =0.32N +0.032 m/s Depth= 0.6 Using…

Q: A haunched (varying depth) reinforced concrete beam is simply supported at both ends, as shown in…

A: Given data- Uniformly distributed factored load =10kN/m, Reinforced concrete beam is given as shown.…

Q: 1. By using Area Moment Method, Determine the deflection at the midspan of the beamshown. 30 kN/m 5…

A: Given Data E = 200 GPA = 200 × 103 N/mm2 I = 1460 × 106 mm4 Find deflection at mid span of beam…

Q: What is Landsat and name 2 Civil Engineering Applications can it be used for?

Q: After a 2-hour storm, a station downstream from a 40 square mile drainage basin measures 9300 cfs as…

Q: In a 200 foot tall water tank, the pressure at the bottom is a. 1960 kPa b. 86 psi c. 25 psi d. 500…

A: Introduction : The given question is related with fluid mechanics . In this question we are provided…

Q: 32 in. L C B y A o I 36 in. 40 in. D 60 in. 27 in.

A: To find tension in cable AB, AC AD

Q: шин A-B-C-D- L AR Journal Bearing problem. $ b .↑. low. Determine Power required (or) Power absorbed…

Q: 1. By using Double Integration Method, Determine the deflection at the midspan of the beam shown. -5…

Q: For constant density flow through this round nozzle, V₁ = 1.7 m/s and V₂ = 20 m/s. The ratio of…

Q: 3 m 3 m X B A C 3 m D E F 3 m G HX 3 m L J K X 60 KN 60 KN

A: Given : A determinate truss in which few member forces are to be found. Members marked X are : KL,…

Q: Discuss the stability and determinacy of the following structures. C=2

A: In general, it is impossible to analyze an unstable structure. Therefore, before performing a…

Q: Determine the reactions at supports A and B. The beam segments AC and CB are connected to eac other…

A: Given data : Determine the reaction at support A and B ?

Q: How to apply grip editing in AutoCAD?

Q: What are the various methods that can be used to determine moisture content in Highway engineering?

A: In highway engineering , determination of water content plays a very important role in the…

Q: A catchment consists of an asphalt pavement that drains into a rectangular concrete channel. The…

A: Given data:- The given asphalt has an average slope is, 0.6% The catchment boundary to the drain is,…

Q: (a) Determine the horizontal Force (Fs) acting on the curved gale.

A: Given :- Length of gate L=4 m radius of gate R= 3 m find the horizontal force acting on the curved…

Q: Question 4. An industrial process produces a by-product compound ‘X’ which exceeds the sewer use…

A: Concentration in industrial waste water = 1780 mg C/L Volume of PFR (Vp)=23 m3 Volume of CSTR…

Q: (b) A catchment consists of an asphalt pavement that drains into a rectangular concrete channel. The…

A: Given: Average of the slope of asphalt surface = 0.6% Distance between catchment boundary and drain…

Q: Problem 612 Compute the midspan value of EI 8 for the beam loaded as shown in Fig. P-612.

A: Using double integration method

Q: The right limb of a simple U-tube manometer containing mercury is open to the atmosphere while the…

A: Given Data- Specific gravity of fluid S1=0.9, Difference in mercury level h2=20 cm, To find- The…

Question

(a) Compare the resultant force acting on the gate if we change the shape of the gate from a triangle to an
equivalent circle. (b) Compare the line of actions, as well. The initial location of the 0.7-m-high and 0.7-m-
wide triangular gate is shown in the figure below.
0.9 m
Water
0.3 m
B
0.7 m
0.7 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution:-

VIEW

Step 2 Solution:-

VIEW

Step 3 Answer:-

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The sector gate UE is submerged in water as shown in the figure. The sector gate is one-twelfth of a circle of radius 5.18 m. It has a length of 7.6 m. Determine the horizontal components (kN) of the resultant force acting on a gate. A Water 30 radius
Two steel pipe columns (E=200,000 MPa,A1=2000mm2,A2=1800mm2)support a rigid beam AC that has a 3.6m overhang BC. The beam supports a linearly varying load of maximum intensity w=75K/nm as shownin the figure.Neglect the weight of the beam AC, and assume that the beam is supported on the two columns such that it transmits load to each column as an axial load.Determine the vertical displacementat end C of the beam, in column 1at A and column 2at B. Answer in mm.
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E= 200,000MPa and a 11.7 Neglect bending of the beam. FF A=640mm2 A=320mm2 D 1.2m 0.8 m 1.2m V 54KN What is the vertical displacement of D when there is no change in temperature in mm?
The triangular gate shown in the figure below is hinged at the B and rests on a smooth floor at A, the horizontal component of the reaction at A therefore being zero. The base of gate is 1.215 meters and perpendicular to the paper. Determine the vertical component of the reaction at A and the horizontal and vertical components of the reaction at B for the following sets of conditions: (a) The vertex of the gate is at B, x= 2.15 meters, y = 3.15 meters and z = 4.15 meters.
Question 1) For the given system in the figure, find the minimum P force that can move the 600 N block upwards. Note: The coefficient of friction between the blocks, and also for the lower surface is u=0.2. The other surface is frictionless u=0 600 N µ=0.2° -P 24 -μ=0.2
The triangular gate shown in the figure below is hinged at the B and rests on a smooth floor at A, the horizontal component of the reaction at A therefore being zero. The base of gate is 1.215 meters and perpendicular to the paper. Determine the vertical component of the reaction at A and the horizontal and vertical components of the reaction at B for the following sets of conditions: (a) The vertex of the gate is at A, x = 1.15 meters, y = 2.15 meters and z =3.15 meters. (b) The vertex of the gate is at B, x= 2.15 meters, y = 3.15 meters and z = 4.15 meters
In (Figure 1), FA = FB = 610 N. Figure B 0.4 m FA FB A 0.3 m Part A Determine the couple moment acting on the pipe assembly and express the result as a Cartesian vector. Enter the x, y and z components of the couple moment separated by commas. Express your answers in newton-meters to three significant figures. Mc = Submit Provide Feedback - ΑΣΦ Request Answer ↓↑ vec ? N.m Next >
A) By means of the transfomations of a couple, replace the force system shown in Figure 3, by a force along line CD and a couple. C 800 kN 300 kN| 300 kN 4 m 2 m 4 m (Figure 3) 4 m
From the figure, determine the reaction at A and D. 900N/m 3m 4m 2m A
The Curve on the surface shown in the figure is having a hydrostatic pressure on one side. The length of gate is Five meters (I at the paper). Determine the following: a. The components of the hydrostatic force acting on the curve surface. (magnitude and direction) b. The Reactions at the hinge (magnitude and direction) Gate 12 m 10 m 8 m
7.) The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to the paper and hinge at O. If the depth of water is 2.50 m, neglecting the weight of the gate calculate the horizontal force P to maintain equilibrium. Use unit weight of water 9.80 kN/m^3. fluid mechanics
The ends of a 0.25kg rod AB are constrained to move along slots cut in a vertical plate as shown. A spring of constant k=3N/m. is attached to end A in such a way that its tension is zero when θ=0°. the rod is released from rest when θ=45° (position 1) until it reaches θ=0° (position 2) Determine the magnitude and velocity at point B (Answer: 46.4 upwards)