In liquid-liquid extraction process, the fraction of solute remaining in phase 1 after n extractions is given by the formula below: 11 = V₁ 1 V₁ + KV₂2 A solute is transfered from water (100 mL) to ether (15 mL). If the distribution coefficient between water and ether is 0.5, and three extractions are performed, what fraction of the solute remains in the aqueous phase after these extractions? a. 0.012 b. 0.752 OC. 0.930 d. 0.230

In liquid-liquid extraction process, the fraction of solute remaining in phase 1 after n extractions is given by the formula below: 11 = V₁ 1 V₁ + KV₂2 A solute is transfered from water (100 mL) to ether (15 mL). If the distribution coefficient between water and ether is 0.5, and three extractions are performed, what fraction of the solute remains in the aqueous phase after these extractions? a. 0.012 b. 0.752 OC. 0.930 d. 0.230

Introductory Chemistry For Today

8th Edition

ISBN:9781285644561

Author:Seager

Publisher:Seager

Chapter7: Solutions And Colloids

Section: Chapter Questions

Problem 7.44E

See similar textbooks

Similar questions

What is the percentage of organic compound that is dissolved in soil pore water that has a porosity of 0.41 and the Kd = 563 L kg-1 ? Report your answer in percentage and enter it is X.Xx10(-X) or X.Xx10(X)
Solute S has a distribution constant of 5.1 between water (phase 1) and hexane (phase 2). A 71.0 mL solution of S in water is extracted three times with 12.0 mL of hexane. Calculate the fraction of S remaining in the aqueous phase. fraction remaining: 0.0575 Incorrect
On the basis of 1,000 mL final solution, it is desired to prepare an aqueous solution containing 20% by weight CuSO4. a) How much blue vitriol(CuSO4.5H2O) crystals must be added to 2.0 L of water at 30oC? b) Calculate the volume of solution formedin m3/m3 of water used at 30oC. c) Find the composition of the solution in mol %, vol%, molarity, molality.Ρwater = 0.996 g/mL ρsolution = 1.2 g/mL
A solute with a partition coeffcient (K-[S)s/S]h) of 5 is extracted from 20 mL of phase 1 into phase 2. What volume of phase 2 is needed to extract 90% of the solute in one extraction? ( (a) 0.44 mL (b) 12 ml (c) 36 ml. (d) 72 ml
64. 20 gm of binary electrolyte (mol. wt. = 100) was dissolved in 500 gm water. Freezing point of solution was found to be -0.74° C [K; 1.86 K molality]. What is the degree of dissociation of the electrolyte. (1) 0% (2) 100% (3) 75% (4) 50%
A 0.25g nonelectrolyte solute (MW=124.5g/mol) is dissolved in 100g solvent (MW-82.90g/mol) have a freezing point depression of 0.209degC. If an electrolyte (i = 2.95) solution is dissolved in the same amount of solvent and results to a freezing point lowering of 0.357degC, what is the concentration of the electrolyte)? 1.1627m 0.0116m 0.1016m 1.1672m
Connected to DESKTOP-VKHKVG3 A solute added to a solvent raises the boiling point of the solution because Molal Boiling-Point Elevation Constants (Kb) and Freezing-Point nts the temperature to cause boiling must be great enough to boil not only the solvent but also the solute. Disconnect the solute particles raise the solvent's vapor pressure, thus requiring a higher temperature to cause boiling. 06:28 / 31:54 "TRU the solute particles lower the solvent's vapor pressure, thus requiring a higher temperature to cause boiling. the solute increases the volume of the solution, and an increase in volume requires an increase in the temperature to reach the boiling point (derived from PV = nRT]).
What is the freezing point of a solution with 5.00 g naphthalene (C10H8) in 444 g benzene (C6H6) with a Kf = 4.90 oC/(moles solute/kg solvent). The freezing point of pure benzene is 5.500 oC. Group of answer choices +5.931 oC -0.070 oC +5.466 oC +7.820 oC +3.180 oC +5.217 oC +5.783 oC +11.070 oC +5.069 oC +5.534 oC
Solute S has a distribution constant of 4.7 between water (phase 1) and hexane (phase 2). A 75.0 mL solution of S in water is extracted seven times with 13.0 mL of hexane. Calculate the fraction of S remaining in the aqueous phase. fraction remaining:
Calculate the boiling point of a solution made by dissolving 17.5 g analine, C&HNH2, in 113 g of water. a) peite beolles How to... calculate the molar mass of a solute from freezing point betovilab geem smt depression or boiling point elevation data. Step 1: Calculate molality from m = ATf= K¢/m or m = ATb/Kb. Express as mol solute/kg solvent biecies Aon Step 2: Using molality as a conversion factor between moles of loo solute and kg of solvent, find the number of moles of solute. Step 3: Use the defining equation for molar mass, MM = g/mol, to calculate the molar mass of the solute.
A solution is prepared by dissolving 40.00 g of MgCl2 (f.w. = 95.211 g mol–1), a non-volatile solute, in enough water (m.w. = 18.02 g mol–1) to result in exactly 2 L of solution at 25 °C. Assume the density of the solution is that of pure water (dsolution = 1.000 g mL–1). The ebullioscopic constant (Kb) for water is 0.513 °C m–1. The cryoscopic constant (Kf) for water is 1.86 °C m–1. The vapor pressure of pure water is 0.0313 atm. Determine the freezing point of the solution.
A solution is prepared by dissolving 40.00 g of MgCl2 (f.w. = 95.211 g mol–1), a non-volatile solute, in enough water (m.w. = 18.02 g mol–1) to result in exactly 2 L of solution at 25 °C. Assume the density of the solution is that of pure water (dsolution = 1.000 g mL–1). The ebullioscopic constant (Kb) for water is 0.513 °C m–1. The cryoscopic constant (Kf) for water is 1.86 °C m–1. The vapor pressure of pure water is 0.0313 atm. Determine the osmotic pressure in atm.