In the gear system shown, the motor applies a torque of 290 N-m to the gear at A. Shaft (1) is a solid 35-mm-diameter shaft, and shaft (2) is a solid 50-mm-diameter shaft. The bearings shown allow free rotation of the shafts. Determine the torque TE provided by the gear system at gear E. B 72 teeth 30 teeth TE (2) E 24 teeth 60 teeth

In the gear system shown, the motor applies a torque of 290 N-m to the gear at A. Shaft (1) is a solid 35-mm-diameter shaft, and shaft (2) is a solid 50-mm-diameter shaft. The bearings shown allow free rotation of the shafts. Determine the torque TE provided by the gear system at gear E. B 72 teeth 30 teeth TE (2) E 24 teeth 60 teeth

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3.27 The two identical shafts, 1 and 2, are built into supports at their left ends. Gears mounted on their right ends engage a third gear that is attached to shaft 3. Determine the torques in shafts 1 and 2 when the 500-N · m torque is applied to shaft 3. 40 500 Nm 80 Dimensions in mm -8-
Each of two gears in a mesh has 60 teeth and a module of 6 mm. The teeth are of involute profile. The arc of contact is 2.5 times the circular pitch. Determine the addendum
A 1. The splined ends and gears attached to the A-36 steel shaft are subjected to the torques shown. Determine the angle of twist of end B with respect to end A. The shaft has a diameter of 40 300 N·m 300 mm 500 N-m 400 mm 200 N-m 500 mm 400 N-m
The four rigid gears, loaded as shown in Fig. (a), are attached to a 2-in.-diameter steel shaft. Compute the angle θ of rotation of gearA relative to gear D. Use G= 12×106 psi for the shaft
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel -20KW JOKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O f segment Co is to be replaced lay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 86cm and 37cm respectively. If driven shaft runs with 10 r.p.s,determine the following; ( 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 8mm
Determine the gear forces if Gear 1 is rotating at 600 rpm and transmitting 250 kW power. The module of the gears is m=2,5 mm and the pressure angle – a = 20°.
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 if its gearbox 5th gear is selected. The gear's teeth are of involute form with a module of 8 mm, an addendum is double the module, and the pressure angle is equal to 20°. 1.1. If the driving shaft of the front wheels of the truck is connected to the output shaft of the gearbox, determine the number of teeth on the pinion to avoid interference and the corresponding number of teeth on the gear wheel. 1.2. Calculate the gear maximum velocity of sliding.
The shafts are made of steel with shear modulus of 75 GPa. Determine the angle of twist of gear B if a torque of 25 kN·m is applied to gear B. Both shafts have the same diameter of 100 mm. (Hint: for the meshing cylindrical gears, i.e. gear C and D, the angle of twist need to time the radius of the gear while applying the equation of compatibility.)
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. -20KW 7OKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O If segment Co is to be replaced ay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
Shafts ab and ce are support by pillow bearing blocks as shown. Compute the angle of twist at point a. Report your answer in degrees to two decimal places. 35 in A Y bearing bearing gear c: radius 2.0 in 2 in-k gear b: shaft ab: shaft ce: radius 5.0 in b a radius 0.5 in 5 in-k radius = 0.7 in d. bearing e bearing all shafts: G = 12000 ksi 25 in 30 in
O A. Given a homogenous shaft with length L, radius R, and modulus of rigidity G, if the internal torque along the shaft is given by the equation T(x) = 0.5x, what is the magnitude of the angle of twist at æ = L? Select one: O B L 4.JG O C. TG O D. E