Match the items in List 1 (Name of field exploration) with those in List 2 (soil properties) and select the correct option. Use codes for matching List 1 P. R. Cyclic Pile load test Q. Plate Bearing test 2. S. Pressure meter test 1. Standard penetration test 3. List 2 Modulus of subgrade reaction Relative density and strength Skin friction and point bearing resistance 4. Elastic constants

Match the items in List 1 (Name of field exploration) with those in List 2 (soil properties) and select the correct option. Use codes for matching List 1 P. R. Cyclic Pile load test Q. Plate Bearing test 2. S. Pressure meter test 1. Standard penetration test 3. List 2 Modulus of subgrade reaction Relative density and strength Skin friction and point bearing resistance 4. Elastic constants

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.13P

See similar textbooks

Similar questions

A frictional pile with a circular cross- section (diameter = D) is pushed into the soil to a distance (L) and then it is %3D subjected to an axial force (P) on its top end. Derive a formula to calculate the normal stress in any section x. f N/mm2 D Cross section Maximum size for new files: 128MB Files
Define the Purkaystha and Char reduction factor method ?
m DrahmedsoilMechanicsnoteschapter5.pdf Downloads/DrahmedsoilMechanicsnoteschapter5.pdf Example 5.15 A sheet pile wall drove into silty having 5*10-8 m/sec. find the quantity of soil a 7 m permeability of 1.75 m 15m seepage, pore water 1.0m 3.5 m 0.75m pressure at points (A to J), and exit gradient. 7 m Impermeable la Solution • The sheet pile wall length is in direction perpendicular to the page • The problem is two-dimensional flow • LB is upstream equipotential line • JK is downstream equipotential line • BF, FJ, and MN is flow lines • H = 7- 1.75 = 5.25 m, Nr = 4, Na = 8 = 5. 10-8. 5.25 = 13.125 + 10-8 m/sec/m length q = kH The difference in the total head is 5.25m and the Na = 8 so in each drop. loose 5.25/8 = 0.656m
Can you please give atleast 2 specific situations requiring grouting then explain
Design the anchored sheet pile wall supporting a loose sand fill as shown in the following Figure. GWT is at the same height on both sides, and assume yw=10kN/m³. Based on the log spiral solutions, the Ka for the loose sand is 0.3 while the K₂ and Kp for the dense sand are 0.2 and 13.125, respectively. Using the fixed earth support method, do the following: a) For a factor of safety of 2 on the passive resistance, determine the requirea depth of penetration depth, D. (initial trial with D'=1.5m) b) Determine the bending moment and the anchor load. c) Select a sheet pile section from the Table 9.1 (E-210x10³ MN/m² and fa-210 MN/m²) D O 7.0m. Yt = 16.5 kN/m³ $' = 30° Z Loose sand fill: Yt 19.5 kN/m3 $' = 30° Dense sand: Yt = 21 kN/m³ $' = 40° q=10 1.5m. 0.5m. kN/m²
Define sand-cone method.
What is Compaction grouting? Describe its procedure.
Describe the installation process of pile foundation.
Consolidated Undrained Test....
A nign rise bullding wll be bult in a reclalmed area in Metro Manila. Concrete piles will be used as its founcation with detalls ana plans as follows: 0.875m 1.800m 1.800m 1.800m 1.800m 1.800m 1.800m 0.875m 0.875m 1.800m C-1 C-2 1.800m 1.800m 1.800m C-1 C-2 1.800m 1.800m
State the method to determine the N-value of soil and the normal N-value required for supporting friction piles
. If on-site slump test fails, should engineers allow thw contractor to continue the conctreting work, Explain.