Outdoor air conditions are: 28°C db, 19.5°C wb Return air conditions are: 22°C db, 50% RH. The mixture air condition outlet the cooling coil are: 10°C db, 0.00735 kg/kgda Draw the system on the Psychrometric chart, then calculate: 1. Cooling coil load. 2. Room sensible heat. 3. Room latent heat. 4. Fresh (outdoor) load. 5. Duct and fan heat gain 6. Sensible heat ratio SHR. If the supply air temperature increases with a value 1ºK due to fan motor heat gain and 2ºK due to duct heat gain.

Outdoor air conditions are: 28°C db, 19.5°C wb Return air conditions are: 22°C db, 50% RH. The mixture air condition outlet the cooling coil are: 10°C db, 0.00735 kg/kgda Draw the system on the Psychrometric chart, then calculate: 1. Cooling coil load. 2. Room sensible heat. 3. Room latent heat. 4. Fresh (outdoor) load. 5. Duct and fan heat gain 6. Sensible heat ratio SHR. If the supply air temperature increases with a value 1ºK due to fan motor heat gain and 2ºK due to duct heat gain.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An air conditioning system is designed under the following conditions Outdoor conditions; 30°C dbt, 75% RH Required indoor conditions; 22°C dbt, 70% RH Amount of free air circulated; 3.33 m/sec Coil dew point temperature; 14°C The required condition is achieved first by cooling and dehumi dification and then by heating. Estimate (1) Capacity of cooling coil intons and its efficiency. (ii) Capacity of heating coil in kW. ii) Amount of water vapour removed kg/sec.
The inside design conditions for a conditioned space are 20.1 degree C dry-bulb and15.2 degree C wet-bulb. The air temperature increases 10.6 degree C as it passes through theconditioned space. The apparatus dew point is 11.9 degree C. The heat transfer rate is 456kW. What is most nearly the volumetric flow rate of the air passing through thespace?A. 12 m3/s B. 19 m3/s C. 22 m3/s D. 36 m3/s
Using Double Integration Method
I (a) Explain the steps involved in representing the natural and mechanically driven air flows within a building using the nodal network method.
A R22 refrigeration system is used to operate between 45degC and -30degC. The total cooling capacity is 350 kW. a. What is the ideal COP of the system? b. What is the heat rejected by the system? c. What is the total power consumed by the system? There are several steps made to improve the performance of the system. What happens to the COP, heat rejected and power consumed by the system when: d. For the same evaporator and condenser pressure, the temperature at the entrance of the compressor is -20degC, and the inlet to the expansion valve is subcooled by 5degC. Due to the wide temperature gap, it is decided to use a two-stage refrigeration system using flash gas removal and optimal intercooling operation in a flash chamber. What happens to the COP, heat rejected and power consumed by the system when: e. Having a low pressure and high-pressure compression. f. Two evaporators and two compressors, with the lower temperature evaporator having a cooling capacity of 225 kW. Notes: The…
Hello Sir,Good Morning.I have a question in my homework related thermodynamics lesson. The following below is my question. Please advice. Thank you. Regards,Irfan An air conditioning system is used to keep the house at 65°F when the outside temperature is 85°F. The house gets heat through the walls and windows at a rate of 810 Btu/min, and the rate of heat generation inside the house from occupants, lights, and equipment is 120 Btu/min. Determine the minimum power input required for this air conditioning system.
Oven Temperature 0 wwwwww Valve ↑y Steam B Piston Oil Supply H Working Cylinder Fig. Q3 Fig. Q3 shows an arrangement for controlling the temperature of a steam heated oven. utilizing temperature sensitive bellows and a hydraulic servomechanism. An increase in oven temperature causes the bellows to expand and the left end of the 'walking beam' ABC to move downwards. thus activating the hydraulic mechanism. The end C of the walking beam actuates a valve to reduce or increase the steam flow into the oven depending on the temperature in the oven. When .x is zero the beam ABC whose mid-point is B, is horizontal. Given that, (a) oil flow in the servomechanism per unit displacement (b) area of cross section of the piston in the working cylinder -Q = A (c) heat transfer across the walls of bellows to the thermos- sensitive fluid in the bellows =q=H(0-1) where I' is the temperature of the fluid inside the bellows and H is a constant. (d) rate of change of temperature in the bellow's fluid Kq…
6. A Thomas meter is located in an air duct of 2 sq ft cross-sectional area. The air weighs 0.083 lb per cu ft, and its specific heat is 0.24. Assume a controlled temperature differential of 5° and heater potential of 110 volts. Plot the velocity as abscissa and amperage as ordinate for veloc- ity 0 to 300 ft per min. Assume constant amperage of 3, and plot tem- perature difference against velocity. Discuss the curves from the stand- point of accuracy of the system. J: よ itet legeted oulindriool oir tube
Refrigerant condenses in the tubes of a cross flow heat exchanger at 41 °C, 16.7 MJ/hr is rejected form the refrigerant by air "c= 1005 J/kg.K". Air enters at 24 °C and leaves at 37 ;c. What is heat transfer area of the refrigerant side (m) when the overall heat transfer coefficient refrigerant side on the is 151 W/m".°C? Hint use LMTD method and assume a correction coefficient of 100%
QUESTION 3 A manufacturer conducted an experiment for an evaporator capacity 500 kW cooling and designed for high COP of 2 when using lithium bromide plus water in an absorption refrigeration system. The evaporator operates 20 C, condenser 40 C & absorber 45 C supplying 1.4 kg/s of water plus lithium bromide solution to the generator. For a condenser size of 650 kW, determine: Show in your solution paper: Chart reading for Concentration and Enthalphy of solution being pumped Provide in the Answer Box: Enthalpy of solution being pumped in kJ/kg
DS Community Downl... Haritalar EOkuma list iş İÇİN Giriş yap 口口山凸9 İNGİLİZCE An air-cooled condenser is used to condense isobutane in a dual geothermal power plant. Isobutane, air entering at 22 oC with a flow of 18 kg/s (cp = 1.0 kJ / kg.K)is condensed at 85 oC. The total heat transfer coefficient for this heat exchanger is 2400 W/m2.K and surface area is 2.6 m2. What is the output temperature of the air? Çeviri yap: Google Bing
The Lithium Bromide water absorption cycle shown in the figure operates at the following temperatures: Generator, 5°C; Condenser, 35°C; Evaporators, 5°C; and Absorber, 30°C. The flow rate of solution delivered by the pump is 0.4 kg/sec. Determine the following: What is the amount of heat, in kilowatts, rejected at the absorber? a. 71.8 b. 287.4 c. 205.3 d. 146.4 e. 104.5 What is the Absorber System Coefficient of Performance, in percentile? a. 146.4 b. 71.8 c. 205.3 d. 104.5 e. 287.4 What is the mass flow rate, in kg/sec, of the fluid at line 5? a. 0.129 b. 0.252 c. 0.180 d. 0.353 e. 0.092