Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. The wind turbine will be installed in a wooded area, full of trees. The data from the Meteorological office says that the wind speed at a height of 10 m in the selected area is: 8.25 m/s. This is to be used as the design speed. 1. If the average wind speed at the turbine height is expected to be 6.0 m/s (IEC Class IIIA) over the full year, calculate the expected energy that would be produced by this wind farm in one year.

Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. The wind turbine will be installed in a wooded area, full of trees. The data from the Meteorological office says that the wind speed at a height of 10 m in the selected area is: 8.25 m/s. This is to be used as the design speed. 1. If the average wind speed at the turbine height is expected to be 6.0 m/s (IEC Class IIIA) over the full year, calculate the expected energy that would be produced by this wind farm in one year.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter7: Relays

Section: Chapter Questions

Problem 9SQ: What is optoisolation?

See similar textbooks

Similar questions

a) Determine total admittance and impedance. b) Draw admittance diagram and impedance diagram. c) Determine the values of C and L. d) Determine the voltage ?? ⃗ and the currents ?? (Se image ! last task)
Part 2: Analysis and selection of the Wind Turbine.The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. 1. What are the two closed loop control systems that are used generally in wind turbines? How do they work? 2. Calculate the power density of the input power from the wind when the wind is blowing at the rated wind speed at the turbine height. Clearly show your steps in details.
With schematic diagram, explain the Wind Power Plant.
Marked out of 1.50 P Flag question 13. i) The data for a wind turbine is given below: Wind speed = 14 meters/sec, Length of blade = 10 meter. Choose the correct statement for this wind turbine. a. The input wind power to the turbine is 258 KW b. The input wind power to the turbine is 51.7KW c. The input wind power to the turbine is 25.8KW d. The input wind power to the turbine is 517KW 13. ii) Refer to the above wind turbine choose the correct statement a. The wind rotor swept area is 40square meters. b. The wind rotor swept area is 62.4 square meters. c. The wind rotor swept area is 314 square meters. d. The wind rotor swept area is 31.4 square meters. O O O O
Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm. The turbine that has been selected by the local contractor is an Enercon wind turbine. The specifications of all the available Enercon wind turbine is shown in the attached datasheet. 1. Decide on the required number of wind turbines needed. 2. In your own words, explain what the Betz limit for wind turbines means.
11. Describe the operation of a vector impedance meter with the help of a block diagram. Explain the function of each block.
The waveform of a voltage source is shown in the given figure. Let A = 2 and B = -3.8. Determine the average power supplied to a 1-ohm resistor connected across the voltage source. The average power supplied to a 1-ohm resistor connected across the voltage source is _______ W.
The waveform of a voltage source is shown in the given figure. Let A = 2 and B = -3.8. Determine the average current supplied to a 10-ohm resistor connected across the voltage source. The average current supplied to a 10-ohm resistor connected across the voltage source is ______A.
What is optoisolation?
Explain the concept of phasor measurement units (PMUs) and their significance in power system monitoring.
4. Explain the relationship between back emf E, terminal voltage V and coil voltage drop IR in DC motor and generator respectively. i. Describe how the field strength affect the performance of DC motor and generator. ii. Explain how an external resister changes the DC motor and generator performance.
7.a. Photoelectric eye alignment is typically a PM task for a(n)A. electrician.B. lubricator.C. machine operator.D. mechanic.7.b. Mean time before failure describesA. how long it will take between failures at your plant.B. how long before one component in a group will fail.C. how a failure will occur on a component that’s inside a machine.D. the amount of time a component will last when it’s heavily loaded.7.c. Under an ISO 9000 program, which one of the following employees is responsible for checkingcompleted work to make sure it has been performed to company specifications?A. The maintenance general managerB. The PM program administratorC. A shop foremanD. A maintenance technician