Q.1: A shaft composed of segments AB, BC is fixed between the two walls at 4 and C and loaded as shown in Figure below, For steel has a 25 mm circular cross section, shearing modulus G = 83 GPa. For aluminum has a 30 mm circular cross section, shearing modulus G = 28 GPa Determine: The two torques at supports A and C 2AN.m B Steel Di-25mm aluminum Di-30nm G-83GPa G-28GPa

Q.1: A shaft composed of segments AB, BC is fixed between the two walls at 4 and C and loaded as shown in Figure below, For steel has a 25 mm circular cross section, shearing modulus G = 83 GPa. For aluminum has a 30 mm circular cross section, shearing modulus G = 28 GPa Determine: The two torques at supports A and C 2AN.m B Steel Di-25mm aluminum Di-30nm G-83GPa G-28GPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

022 Plate 3-Method of Consistent Deformation Determine the force in member CD of the truss shown in the figure. Circled values are areas in square inches. E is constant. FEU ALASANC FEU DEIMAN What is the horizontal Reaction at A? [Select] What is the Verticall Reaction at A? [Select] What is the Vertical Reaction at B? [Select] What is the horizontal Reaction at C? [Select] O II W -10 ft- B D 30 k (2) Wo -15 ft S 0 C 20 ft C Technology Driven by Innovation 208C Light rain
The rigid bar BDE is supported by two rods AB and CD. Rod AB is made of aluminum (Eal = 70 GPa) and has a cross-sectional area of AAB= 400 mm2; Rod CD is made of steel (Esteel = 200 GPa) and has a cross-sectional area of ACD = 500 mm2. The load P = 31 kN is applied at point E as shown in the figure. [LAB = 0.3 m, LCD = 0.4 m, a = 0.2 m, b = 0.4 m] Determine the internal force of rod AB?KN Determine the displacement of point B?in mm Determine the displacement of point E?
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 633 mm2. For the 36 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places
The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
THE DIAGONAL MEMBERS IN THE CENTER PANELS OF THE TRUSS SHOWN ARE VERY SLENDER AND CAN ACT ONLY IN TENSION; SUCH MEMBERS ARE KNOWN AS COUNTERS. DETERMINE THE FORCE IN MEMBER DE AND IN THE COUNTERS THAT ARE ACTING UNDER THE GIVEN LOADING. (15 PTS) Counters ARA B F 6 ft H C E G 3 kips 6 kips 9 kips -S ft- <8 ft- S ft→|<-S ft-
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 619 mm?. For the 41 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places 04 m 0.3 m E 0.4 m 0.2 m
Q.1: A shaft composed of segments AB, BC is fixed between the two walls at 4 and C and loaded as shown in Figure below. For steel has a 25 mm circular cross section, shearing modulus G = 83 GPa. For aluminum has a 30 mm circular cross section, shearing modulus G = 28 GPa Determine: The two torques at supports A and C 2 N.m B 3m 4m Steel aluminum Di-30mm Di-25mm G-83GPA G-28GPA
Aen = a0 © @2 Z Q23-7-2018p.. Q1: A railway ridge consisting of truss construction as shown in the Figure below, this truss is supported by A and B. The forces on joints il and V are i the uss result from a i crossing the railway bridge Determine the following: (a)the reactions forces in A and B (b)the forces of the truss members in joints (1.1, I and 1V) >
4. The shaft consisting of steel and aluminum segments carries the torques T and 2T as shown in the figure. Find the largest allowable value of T if the allowable shear stresses are 83 MPa for steel and 55 MPa for aluminum, and the angle of rotation at the free end must not exceed 6°. Use G = 83GPa for steel and 28 GPa for aluminum. 2T 50 mm dia T 40 mm dia Steel 900 mm Aluminum 600 mm
Problem # 4. A 12-mm-diameter steel E 200 GPa] rod (2) is connected to a 30mm wide by 8 mm thick rectangular aluminum [E 70 GPa] bar (1), as shown. required to Determine the force P stretch the assembly 10.0 mm. Ans: = A (1) 0.45 m B (2) 1.30 m - C
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP
P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar AE is an aluminium alloy [EAE 70 GPa] with a cross-sectional area of AAE = 2,400 mm². Bar CF is a bronze alloy [ECF = 100 GPa] with a cross-sectional area of ACF = 6,000 mm². A downward load P=298 kN is applied at point B. Determine the normal stress created in bras AE and CF. E 2.9 m 0.8 m B P 1.5 m 3.3 m 1.2 m D