BkcBZYhc850ZmX4-RzV7i6yWprtMcdra5me-w_Og/formResponseThe DAC with inputs and outputs shown in figure below, the fault in the circuit isinnote (all the values is in approximate range )RFR1200120kU1R260kR374130kR415k- 13.2 mV- 15.6 mV- 29.9 mV-65.6 mV-79.9 mV- 82.2 mV- 96.5 mVR1 OR2000000100100011000010011010101111011110III0000

In the given circuit voltage source can be used in the current sources . The voltage at one end of…

Answered: RF R1 200 120k U1 R2 60k R3 741 30k R4…

Engineering

Electrical Engineering

RF R1 200 120k U1 R2 60k R3 741 30k R4 15k

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Signal and system problem plz explain every step how do this step
VI Ru Ri Vz I, Io R2 = 3837.79 O. R3 = 3989.3 Q. %3D R4 = 2898.06 Q. V1 = 4.8 V. V2 = 8.1 V. 11 = 0.0099 A Determine the following: a.) The output current lo %3D
Explain dual slope ADC and successive approximation ADC with neat block diagram and compare the two approaches
Q 1. Determine the output voltage of the Digital-to-Analog Converter (DAC) in Figure 1(a) and plot it in Figure 1(c). The sequence of the four digit binary codes represented by the waveforms in Figure 1(b) are applied to the inputs. A high level is a binary 1and a low level is a binary 0. The least significant binary digit is Do. Do o D₁ 0- 200 ΚΩ www D₂ 0 100 ΚΩ www 50 ΚΩ www 25 ΚΩ D3 0 M 0 -0.25 -0.50 -0.75 -1.00 -1.25 -1.50 -1.75 -2.00 -2.25 -2.50 -2.75 -3.00 -3.25 -3.50 -3.75 (a) Vout (V) R₁ 10 ΚΩ o Vout +5 V Do 0 +5 V D₁ 0 +5 V 0 +5 V 0 D₂ D3 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 non (c) Figure 1 I 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 ||||| (b) Binary input
For the signal flow graph of the given figure, consider the following statements 1. It has three forward paths 2. It has three individual loops 3. It has two non touching loops Out of above the correct statements are X2 X3
if you design differentiator to differentiate input signal varies in frequency between 1 KHz and 20 KHz then find. Cutoff frequency=.......... 01000 O2000 03000 O4000
Calculate the output for the given circuit . R2 R2 Voa R1 Let the values are R1=775.8ohm,R2=506.8 ohm .The error voltage is =8.3 Volt and the initial value of output is 3.7 Volt. Vout = volt.
Design a R-2R Ladder DAC using a reference voltage of (1OV) and a full scale of the output analogue voltage is (9.9975585V). If the current pass through the LSB is 1mA.1- What will be the current pass through 3rd LSB, 5th LSB and MSB. 2- Determine the Vo for an input codes (101010101010), (000101001110) and (001110010111). 4 14bit, 1mA and 6.665v, 0.9215v, 3.234v O 12bit, 1mA and 6.665v, 0.815v, 2.234v O 12bit, 1mA and 5.565v, 1.815v, 2.534v 14bit, 1mA and 6.665v, 0.8345v, 3.234v
5. The following Data input and data select waveforms are applied to a De-Multiplexer. Determine the output waveform. Data in Spi
2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref +
M1 and M2 are matched, what is the output common mode voltage? Draw the output wave form if Vi is a sine wave of 10MHz and peak amplitude of Vdd/4, assume high gm, long channel, find the output signal shape, frequency and peak to peak amplitude, Rin ww RF VDD M2 M1 Rout
JAL D Figure P6 Determine the output, X, for a 2-input AND gate with the input waveforms shown in Figure P6. Show the proper relationship of output to inputs with a timing diagram. B A B X