S Q2. The double pulleys are fastened together to form a rigid unit. If V₁ = 9 and VB = 3 compute the angular velocity of the double pulley and the velocity of the load L. Use vector method. Also draw velocity-vector diagram of either pulley. Explain each step. Any illogical step will not be accepted. Refer to the following figure. UB B 600 mm- 400 mm. O O L 1114

S Q2. The double pulleys are fastened together to form a rigid unit. If V₁ = 9 and VB = 3 compute the angular velocity of the double pulley and the velocity of the load L. Use vector method. Also draw velocity-vector diagram of either pulley. Explain each step. Any illogical step will not be accepted. Refer to the following figure. UB B 600 mm- 400 mm. O O L 1114

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Find VR and Vc AO2=30mm В AB=60mm AC=80mm BC=45mm A B04=50mm 0,= 2 rad/s 0204=70mm 04 O4 Angle of 02A is 45 degrees with respect to positive x-axis.Drawing is not in scale redraw if possible and applicable.
SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer for Part A, with THE CORRECT UNITS ( should be ft/sec) Thank you. Express your answer to three significant figures and include appropriate units. DRAW the kinematic diagram and label it for this problem as well Thank you
SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer for Part A, with THE CORRECT UNITS ( should be rad/sec^2) Thank you. Express your answer to three significant figures and include appropriate units. DRAW the kinematic diagram and label it
! Required information A rope connecting points A and B supports the force Fshown in the figure. Write expressions using Cartesian vector representation for the following. Take L = 8 ft and F= 12 Ib. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. y B 30° ÜBA : the unit vector from B to A. ÜBA
actuating limb angular position is given as 812= 60° and the speed of the mechanism is given as é12= 50 rad/s. Do the following operations respectively. Kinematic diagram and limb dimensions are given below, in the arm slide mechanism, the a-Write the Vector Closure Equation into scalar form. b-Find S13, 014 by position analysis. C-Find Sı3Ö14 by analyzing velocity. A9A = r2 = 0.2 m A,Bo = r = 0.5 m 012 = 60° 012 = 50 rad/s S13 014 Bo 012 ri A0
A pole extends from the origin to point A. A wire connects points A and B. Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value a 4.5 m 2 m 2.5 m 1.5 m a. Determine the position vector from point A to origin (r AO), express as a cartesian vector. b. Determine the position vector from point A to B (7AB), express as a cartesian vector. Round your final answers to 3 significant figures. k) m AO k) m TAB
SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer for Part A, , with THE CORRECT UNITS. (m/sec^)Thank you. Express your answer to three significant figures and include appropriate units. DRAW the kinematic diagram and label it for this problem as well
In the figure shown, I=170mm, b-70mm and wAB=1100rpm (clockwise) Solve for (a) the velocity(m/s) of Pwhen 0-50° (b) the angular velocity(rad/s) of BD when 0-50°. (Note: WAB is constant)
These are the formula for the topic Answer the problem 1 complete solution please thank youu
The figure shows a concept for a hand pump used for increasing oil pressure in a hydraulic line. Analytically determine the displacement of the piston as the handle rotates 12.5° counterclockwise. Also, input the corresponding initial and final vertical position of the piston the space provided. (Use 2 decimal places for the final answer.) 5" B 12° Offset 12° A 1.5" Initial Vertical Position of the Piston (inches) = 10.07 Final Vertical Position of the Piston (inches) = 8.45 DISPLACEMENT (inches) = 1.62
SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer for Part A, and Part B , with THE CORRECT UNITS ( should be m/sec^2) Thank you. Express your answer to three significant figures and include appropriate units. DRAW the kinematic diagram and label it for this problem as well
-Drawing the relationship between the linear displacement (x) and the angle (theta) in practice through the readings you want. The device then unifies the slope at different points of the rest diagram to practically find the values of the free velocity of the slide and draw the relationship between the linear velocity and the angle (theta), which is a sinusoidal function and be a cosine function. Note:-r=25 mm, l=150 mm.