SAE 99W10, a new motor oil, has a dynamic viscosity of 0.21 kilograms per meter second [kg/(m s)] and a specific gravity of 0.866. E Click the icon to view the typical units of viscosity. Click the icon to view density of water. Click the icon to view the conversion table. (a) What is the dynamic viscosity of the motor oil in units of centipoise [cP]? The dynamic viscosity of the motor oil is 210 cP. (Round your answer to the nearest whole number.) (b) What is the kinematic viscosity of the motor oil in units of stokes [St]? The kinematic viscosity of the motor oil is St. (Round your answer to two decimal places.)

SAE 99W10, a new motor oil, has a dynamic viscosity of 0.21 kilograms per meter second [kg/(m s)] and a specific gravity of 0.866. E Click the icon to view the typical units of viscosity. Click the icon to view density of water. Click the icon to view the conversion table. (a) What is the dynamic viscosity of the motor oil in units of centipoise [cP]? The dynamic viscosity of the motor oil is 210 cP. (Round your answer to the nearest whole number.) (b) What is the kinematic viscosity of the motor oil in units of stokes [St]? The kinematic viscosity of the motor oil is St. (Round your answer to two decimal places.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are heating motor oil to make it flow better from the original shipping container to the new container you built. You know that the heating rate of the motor oil is 2.50 degrees Celsius per slug second [°C /(slug s)]. Express this heating rate in units of degrees Fahrenheit per pound-mass second [°F/ (lbm s)]. Click the icon to view the conversion table. Click the icon to view the factors for temperature intervals conversion The heating rate is °F / (lbm s). (Round your answer to three decimal places.)
12. Imagine a solar collector for hot tap water in a hot climate. De outdoor temperature is 22 degree Celsius. De tank of the solar collector is placed outside, and the cold water temperature to the collector is 20 degree Celsius. De water flow rate through the collector is 45 liter/hour. De collector is 2 [m2] and the average solar radiation in the time period considered is 1000 [W/m2]. What is the temperature of the hot water to the tank? The efficiency of the collector can be assumed to be 0.7 (we neglect the dependency to the water temperature) (multiple choice, one answer) 34 [OC] 47 [OC] 54 [OC] 67 [OC] 74 [OC]
Task 2. With the use of a plate apparatus with hea flux density sensors, the thermal conductivity coefficient à was investigated for autodaved aerated concrete ofvarious densities and with værying degrees of humidity. Theresults are presented in the tablesin the appendices. Please write your condusions. Density [kg/m'] 300 400 600 15 Moisture content [%] ther mal conductivity coefficient i. [W/m K] 10 15 5 10 10 15 0,0805 0,0900 0,1020 0,1190 0,1200 0,1240 0,1300 0,1400 0,1599 0,1701 01840 0,1900
physical quantities m, r, u, a, and t with dimensions [m] = M, [r]= L, [v] = LT, [a] = LT-2, and [t] = T. Enter the dimensional expression of the quantity on the right-hand side of each equation. Your answers may contain only M, L, T, and exponents. Assume that each of the following equations is dimensionally consistent. F = ma [F] =
The Antoine Equation can be used to estimate vapor pressure at various temperatures for different substances using sets of empirically-derived constants. The equation can be written as: Where for water A = 8.07131, B = 1730.63, C = 233.426, T = temperature [°C], and P = vapor pressure [mmHg]. Note that with these constants the temperature and pressure must be provided in °C and mmHg, respectively. Using the Antoine Equation and the provided constants, what atmospheric pressure (provided in terms of % of standard atmospheric pressure) will permit water to boil at 75 °C?
Complete the following Table for water. For each case, draw a separate T-v diagram and qualitatively mark each thermodynamic state on the diagram. Show all required calculations for full credit. p[kPa] T[°C] v [m³/kg] u [kJ/kg] X state h [kJ/kg] 2260 275 400 700 350 1 2000 20
|The following processes occurs in a rever sible thermodynamic cycle: 1-2: Reversible polytropic compression at pressure X)bar at volume Y)m' to a pressure [Z]bar and specific volume (A]m'/kg. The index of compression may be taken as n. 2-3: Reversibly expansion with expansion index of 2 to pressure [B/bar. 3-1: Reversible cooling at constant volume to the initial state.
A constant volume gas thermometer is used to determine the temperature of an unknown fluid. Pressure data for thermometer in the unknown bath (P) and a Triple Point Cell (P) are given below. P[Torr] 100.0 P [Torr] 127.9 200.0 256.5 300.0 385.8 400.0 516.0 What is the temperature of the unknown fluid bath? explain and show all work please and write clearly
1.1 s) The overall size of the system (i.e. the shell) is 5.8 inch ID and a 27-inch long tube section. Assuming tubes are 1/2 inch in diameter (ignore thickness) and that the tubes are spaced with 1/4 inch between them. Estimate the number of tubes that will fit in the shell. O 36 O 60 O 13 O 46 QUESTION 2 1.22 area [ft²]. Og ft² 5 ft² O 17.66 ft2 10.6 ft2 Regardless of your answer to part 1.1, use 36 as the number of tubes and estimate the total heat transfer
Feeding Rate (R) [g/h] 6 5 1 0 A B 0 1 U 2 3 E D F 4 5 6 7 8 9 Time (t) [h] 10 11 12 13 14 The feeding rate in grams per hour is displayed as a function of time in hours [h] for a bioreactor. Select the phrase that makes the following sentences true. Between points C and D, the feeding rate [Select ] Between points D and E, the feeding rate [Select] The mass of feed in grams [g] added to the bioreactor between points F and G is [Select ] The mass of feed added to the bioreactor between points E and F is zero The mass of feed added to the bioreactor between points H and I is [Select] grams [g].
Q2) SI engine operating at 4000 RPM has a six-liter, V8. The compression ratio rc = 9:1, the volumetric efficiency nV = 0.91, and the bore and stroke are related as stroke S = 0.8 B. Calculate: (a) Stroke length. [cm] (b) Average piston speed. [m/sec] (c) Clearance volume of one cylinder. [cm3] (d) Air flow * [rate into engine. [kg/sec
QUESTION 23 A Wind turbine has a rotor diameter of 33m. At wind speed of 13m/s what is the a power [MW] in the wind?