Situation 44 A simply supported beam as shown in figure below is pin connected at A and supported by a roller at B. It is subjected to a concentrated load of 30 kN at point C. Using Conjugate Beam Method, Assume El is constant, El = 3800 kN.m2. determine the following: a. Deflection of the beam at the midspan/point D, Ymid A 4.00 m 30 kN CD 8.00 m B

Situation 44 A simply supported beam as shown in figure below is pin connected at A and supported by a roller at B. It is subjected to a concentrated load of 30 kN at point C. Using Conjugate Beam Method, Assume El is constant, El = 3800 kN.m2. determine the following: a. Deflection of the beam at the midspan/point D, Ymid A 4.00 m 30 kN CD 8.00 m B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5. For the beam loaded as shown, find the slope at the right support and the deflection at point A. Use E = 200 GPa and 1= 9 x 107 mm4. Use conjugate beam method a CS Scanned with CamScanner 20 kN/m -1.5 m b -4.5 m 10 kN/m ch 1.0 m
Find the slope and deflection at B and E of the beam and loadings shown using area-moment method. The section of the beam is tubular with outer diameter of 500mm and inner diameter of 200mm. E=20GPa. (point B is not an internal hinge). 1800 N-m |2m B 2 m 200 N/m 2 m 2 m JE
IV- Double Integration Method 4. Determine the slope and deflection at B and the maximum deflection for the beam. El is constant. 25 Kips 10 Kips/ft B C 12' 6'
0. For the truss shown below, determine the vertical deflection at point B (AB) and the horizontal deflection at point H (AĦ) using the virtual work method. |50 kN DV |20 kN |20 kN E FV G HV 17 60 kN E = 200 GPa A = 500 mm² 5 m В 2 m 2 m' 2 m' 2 m
IV- Double Integration Method 4. Determine the slope and deflection at B and the maximum deflection for the beam. El is constant. 25 Kips 25 Kips 10 Kips/ft A D В 6' 6' 6'
Problem VII. A simply supported beam of length 7 m. has a concentrated couple of 10 kN m applied clockwise at the left end. Using E= 200000MPa, I= 60 x 106 mm4 23. Find the location of maximum deflection from the applied load. a. 2.759 mm d. 2.655 mm b. 2.959 mm c. 2.395mm deflection of the beam? C 24 What is the maximum a. 2.59 mm b. 2.62 mm c. 2.54 mm d. 2.60 mm B 3. Determine the angle of rotation at the point of application of the couple in degree. b. 0.0012 a. 0.0019 c. 0.19 d. 0.11
Solove deflection at B Use E= 200,000 N/mm2 and 150 mm wide x200 mm high beam - moment area
USE CONJUGATE BEAM METHOD ONLY PLEASE! DON'T USE AMM AND DIM! Use Conjugate Beam Method. The cantilever beam has a rectangular cross section 50 mm wide and 150 mm high. Find the slope and deflection at the free end using CBM. Use E = 10GPA. %3D 4 kN/m 50 mm A 150 mm - 2 m -1.0m →|
Q7 Use method of conjugate beam to determine the slope and deflection at the center of the beam given below. Take E = 200 GPa and I= 4000 cm*. 5 kN 8 kN A EI B 2EI C EI -3 m -- 4 m t2 m -
Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x250 mm section and E = 200 GPa. Show complete and organized solution. a. Vertical Reaction at C in kN. b. Moment Reaction at C in kN-m. c. Deflection at point B in mm. d. Maximum deflection on the beam in mm Given: a- 4m b- 24kN/m c- 9kN
36 The simply supported beam ‘A’ of length L carries a concentrated load P at midspan. Another beam ‘B’ is loaded with a uniformly distributed load such that the total load on the beam is P. Calculate the ratio of maximum deflections between beams A and B. A. 5/8 B. 5/4 C. 4/5 D. 8/5
Q1: Use the conjugate-beam method and determine the deflection of the end C of the cantilever beam. El=30000 kN.m2. 80 kN.m EI 2EI В -3m- 4m