Six years ago, an 80-kW diesel-electric set cost $145,000. The cost index for this class of equipment six years ago was 187 and is now 194. The plant engineering staff was considering a 120-kW unit of the same general design to power a small isolated plant that would have cost $200,145. Based on the information above the plant engineering staff is considering a 100-kW unit of the same general design to power a small isolated plant. Assume we want to add a pre-compressor, which (when isolated and estimated separately) currently costs $10,000. Determine the total cost of the 100-kW unit.

Six years ago, an 80-kW diesel-electric set cost $145,000. The cost index for this class of equipment six years ago was 187 and is now 194. The plant engineering staff was considering a 120-kW unit of the same general design to power a small isolated plant that would have cost $200,145. Based on the information above the plant engineering staff is considering a 100-kW unit of the same general design to power a small isolated plant. Assume we want to add a pre-compressor, which (when isolated and estimated separately) currently costs $10,000. Determine the total cost of the 100-kW unit.

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter17: Energy Conservation

Section: Chapter Questions

Problem 20P

See similar textbooks

Similar questions

Problem- Two turbo-generators, each capacity 25,000 kW, have been installed at a hydel power station. The load on the hydel plant varies from 15,000 kW to 40,000 kW. What is the total installed plant capacity and the load factor.
Problem T3 If the shaft power is 82kw and the cost of the electricity is $0.10 kwh; estimate the cost of the electricity for one hour. Answer $8.2
Please include a diagram. Thank you! You have a piping system in your plant that has gotten old and rusty. The pipe is 2-in. sched 40 steel, 6000 ft long. You find that it takes 35 hp to pump water through the system at a rate of 100 gpm. a. What is the equivalent roughness of the pipe?b. If you replace the pipe with the same size new commercial steel pipe, what percentage savings in the required power would you expect at a flow rate of 100 gpm?
BEC pho is a company that manufactures turbines for power generating plams. BEC recently signed a contract with an independent power producer, Motlakase. According to the contract, BEC agreed to supply a turbine for a Start in the contract rate of 100 megawatts. new power plant owned by Motlakage. BEC guaranteed that the turbine would produce electricity at a In addition to supplying the turbine. BEC's contractual responsibilities included providing technical advice and on-site support during the up, testing and commissioning of the turbine. Motlakase hired Modupi, plant including installing the turbine supplied by BEC.. Modupi Installed the turbine and the construction of the power plant is now almost complete. The contractor is now ready to commission the plant by running a number of tests to make a separate construction contractor, to construct power sure that the turbine is working properly and producing the power at the guaranted rate. years. BEC sent one of its employees, Thabo,…
A steel pipe is having an ID of 13.25" is to be designed to carry 48,000 bbl of oil per day from a midcontinent field refinery 580 miles from the source. The difference in elevation on the two ends of the line is negligible. AT an average temperature involved, the oil has an absolute viscosity of 50 cP and a specific gravity of 0.87. Determine the actual power requirement (in hp) if the efficiency is 65%.
Equipment A: The cost of equipment A is $100/ Hr The volume per cycle is 4 CY / cycle The cycle time is 10 minutes The equipment works 50 min / Hr Equipment B: • The cost of equipment A is $110/ Hr The volume per cycle is 6 CY / cycle The cycle time is 12.5 minutes • The equipment works 50 min / Hr Which Equipment option has lower $ Cost per CY ?
A plant has installed a single suction centrifugal pump with a discharge of 68 m3/hr under 60 m head and running at 1200 rpm. It is proposed to install another pump with double suction but of the same type to operate at 30 m head`and deliver 90 m3/hr. What must be the impeller diameter of the proposed pump if the diameter of the existing pump is 150 mm?
As the project consultant of Green Court engineering consults, you have been contracted by Total Power to present a detailed proposal on an intended project to explore an additional generation unit to increase capacity. a). In your capacity as the project engineer, why is the project necessary? b). Explain briefly the side effects of the project and their remedies c). Discuss the major factors to take into consideration when consulting on such projects .
Design a Fuel Oil Diesel Electric Power Plant with an assign peak cap of 950 Mega Watts. You are to find a suitable location where the energy source is available, and to determine the targeted community you wish to serve. Assume that you can locate your building on a Clay-Compact Soil, with a flat terrain near a Creek, River, or body of water. You are to determine the power-rate you ill charge the power-distributor for each kind of Power Plant,
You are considering purchasing a compact washing machine, and you have the following information: • The Energy Guide claims an estimated yearly electricity use of 350 kW-hrs, based on 8 loads of laundry being washed per week. • The Energy Guide claims an estimated yearly operating cost of $38. This estimate is based on $0.1065 per kW-hr, and eight loads of laundry being washed per week. • Local electricity costs $0.086 per kW-hr. • You wash four loads of laundry per week. Based on this information, first calculate the energy that would be used by this compact washing machine in a year. Then calculate the yearly energy cost. $3.27 $15.34 $19.00 $178.40
A semi open type impeller where installed in a centrifugal pump with an rom of 1,800 and water flow velocity of 45 ft/s, what is the diameter of the impeller to be used?
The nearby town of Bellefonte, PA features the Gamble Mill, an old mill originally used to grind grain into flour - 1800s hydropower. The mill dam, pond, millrace and tail race are still in place and functional. The mill building is now a restaurant (currently for sale), but all the water-works are owned by the borough. The municipal manager wants to put the system back to work as a small hydroelectric system to help supply the borough's electricity. Does this idea make sense? How much power could this system produce? The height difference between the mill race and the tailrace is ten feet (3 meters), and the stream can supply, on average, 100 cubic feet of water per second (2.8 m^3/sec). The planned turbine would be 63% efficient under those conditions. Power (watts) = density of water * height * flow rate acceleration of gravity * coefficient of efficiency NOTE: the coefficient of gravity is 9.81 for this problem Don't round your answers. *