steel bar ABCD consists of three sections: AB is of 30mm diameter and 100 mm long, BC is 20 mm square and 400 mm long, and CD is of 12 mm diameter and 200mm long. The bar is subjected to an axial compressive load which induces a stress of 50 MN/m2 on the largest cross-section. Determine the total decrease in the length of the bar when the load is applied. For steel E = 210GN/m2 .

steel bar ABCD consists of three sections: AB is of 30mm diameter and 100 mm long, BC is 20 mm square and 400 mm long, and CD is of 12 mm diameter and 200mm long. The bar is subjected to an axial compressive load which induces a stress of 50 MN/m2 on the largest cross-section. Determine the total decrease in the length of the bar when the load is applied. For steel E = 210GN/m2 .

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.21P: A slightly tapered bar AB of solid circular crass section and length L is supported at end B and...

See similar textbooks

Similar questions

A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape (sec figure). The column is 24 ft long. The resultant of the axial loads acting on the column is a force P acting with an eccentricity n = 2.0 in. If P = 120 kips, determine the maximum compressive stress ff^ in the column. Determine the allowable load Pallowif the yield stress is ( y =42 ksi and the factor of safety with respect to yielding of the material is n = 2.5.
A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A steel bar ABCD consists of three sections: AB is of 20 mm diameter and 200 mm long, BC is 25 mm square and 400 mm long, and CD is of 12 mm diameter and 200 mm long. The bar is subjected to an axial compressive load which induces a stress of 30 MN/m 2 on the largest cross-section. Determine the total decrease in the length of the bar when the load is applied. For steel E -- 210GN/m 2. [0.272 mm.] Could you please answer this fully? If you use * can you explain whatyou mean by it. Thank you
A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2
3 m Load D 2 m+ 3 m The member AC is made from an aluminium alloy and has a rectangular cross section of 100mm x 10mm. Calculate the stress in member AC if a load of 57.4 kN is applied at point D.
Steel bar with dimensions with (10mm and 10mm) subjected to axial load of * 2000N. Determine the stress P 10mm 10mm L=100 mm
The vertical shaft with a diameter of d = 20 mm is supported by a thrust collar that rests on a 21-mm-thick plate. The thrust collar is 16-mm thick. Assume that the load P causes a compressive stress of 190 MPa in the shaft. If the bearing stress between the thrust collar and the plate is limited to 35 MPa, determine the minimum outer diameter Dcollar that must be used for the thrust collar. Thrust collar area Plate Thrust collar d Dcollar
A steel rod of circular cross section will be used to carry an axial load of 89 kips. The maximum stresses in the rod must be limited to 36 ksi in tension and 16 ksi in shear. Determine the required diameter for the rod.