Straight bevel gears are mainly used to change the change the rotation axis of intersecting shafts. You work as a maintenance engineer for a food packaging company and your supervisor asked you to accurately calculate the dimensions for a set of straight bevel gears used in one of the differentia gearboxes at the facility. The gear type is an uncrowned straight-bevel pinion has 22 teeth, a module of 4.5 mm, and a transmission accuracy number of 5. The pinion and the gear are made of through-hardened steel, both having core and case hardnesses of 210 Brinell. The pinion drives the 24-tooth bevel gear. The shaft angle is 90°, the pinion speed is 1600 rev/min, the face width is 23 mm, and the norma pressure angle is 20°. Both gears have an outboard mounting. Find: a) The power rating based on AGMA pitting resistance if the life goal is 10° revolutions of the pinion at 0.98 reliability.

Straight bevel gears are mainly used to change the change the rotation axis of intersecting shafts. You work as a maintenance engineer for a food packaging company and your supervisor asked you to accurately calculate the dimensions for a set of straight bevel gears used in one of the differentia gearboxes at the facility. The gear type is an uncrowned straight-bevel pinion has 22 teeth, a module of 4.5 mm, and a transmission accuracy number of 5. The pinion and the gear are made of through-hardened steel, both having core and case hardnesses of 210 Brinell. The pinion drives the 24-tooth bevel gear. The shaft angle is 90°, the pinion speed is 1600 rev/min, the face width is 23 mm, and the norma pressure angle is 20°. Both gears have an outboard mounting. Find: a) The power rating based on AGMA pitting resistance if the life goal is 10° revolutions of the pinion at 0.98 reliability.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure shown below illustrates the gears in a speed-change gearbox used in machine tool applications. By sliding the cluster gears on shafts Band C, nine speed changes can be obtained as shown in Table given below. The problem of the machine tool designer is to select tooth numbers for the various gears (2 to 10) so as to produce a reasonable distribution of speeds for the output shaft. The gears 2, 6 and 9 are having 20, 25 and 50 teeth respectively. The input shaft speed is 450 rpm and the output speed can vary from 137 rpm to 580 rpm depending on the sequence of the gears. If the output speed obtained through the gear sequence 2-5-5-8 is 257 rpm and if the minimum and maximum number of teeth in the gear system are 20 and 50 respectively, (i) Suitable tooth numbers for the remaining gears (3,4,5,7,8 & 10)
7. The following data relate to a pair of 20° involute gears in mesh : Module = 6 mm, Number of teeth on pinion = 17, Number of teeth on gear = 49; Addenda on pinion and gear wheel = 1 module. Find : (a) The number of pairs of teeth in contact (b) The angle turned through by the pinion and the gear wheel when one pair of teeth is in contact (c) The ratio of sliding to rolling motion when the tip of a tooth on the larger wheel (i) is just making contact (ii) is just leaving contact with its mating tooth (iii) is at the pitch point.
Two identical involute, spur gears are in mesh. The module is 4 mm and each gear has 22 teeth If the operating pressure angle is 20° The minimum value of addendum needed to ensure continuous transmission of motion is
The following data is for two meshing gears Velocity ratio=0.5 Module =5 mm, Pressure angle =20° Centre distance = 250 mm Determine the number of teeth and the base circle radius of the gear wheel.
OL Two involute gears of 20° pressure angle are in mesh The number of teeth on pinion is 20 and the gear ratio is 2. If the pitch expressed in module is 5 mm and the pitch line speed is 1.2 m/s, assuming addendum as standard and equal to one module, find: 1 The angle turned through by pinion when one pair of teeth is in mesh; and 2 The maximum velocity of sliding.
The figure shows a schematic representation of a gear system. The gears are meshed with one another and can therefore not slip. The ring gear R is fixed, i.e. wR = 0. Gear A has an inner hub with radius rA(inner) = 0.3 m which is fixed to the rest of the gear, having a radius of FAlouter) = 0.8 m, and moves together as a unit. Gear A is in mesh with gear B which has a diameter of de = 1.5 m. Gear B has a clockwise angular velocity of wg = 2.1 rad/s. Determine the angular speed of gear A. B TA(outer R
OL Two involute gears of 20 pressure angie are in mesh. The nomber of teeth on pinion is 20 and the gear ratio is 2. If the pitch expressed in module is 5 mm and the pitch line speed is 1.2 m/s, assuming addendum as standard and equal to one module, find: 1 The angle turnad through by pinion when one pair of teeth is in mesh; and 2 The maximum veloctty of sitding
10. The figure below illustrates the gears in a speed-change gearbox used in machine tool applications. By sliding the cluster gears on shafts B and C, nine speed changes can be obtained. The problem of the machine tool designer is to select tooth numbers for the various gears so as to produce a reasonable distribution of speeds for the output shaft. The smallest and largest gears are gears 2 and 9, respectively. Using 20 teeth and 45teeth for these gears, determine a set of suitable tooth numbers for the remaining gears. What are the corresponding speeds of the output shaft? 3 w = 450 rev/min Input 7 61 B 8 10 Output w = 137 to 580 rev/min
Question 2 PLATE TYPE FORMAT HAND DRAWN & HAND WRITTEN A gear train is to be devised using all external gears on parallel shafts. Use no more than 150 teeth in any gear and 20° full depth involute teeth. The input speed is 30.5433 rad/min and the output is 4.24697 E-2 radis to 4.36333 E-2 rad/s. Ensure there is no interference and sketch the layout your design.
1. Given a gear of 32 teeth and 6 diametral pitch. Find the pitch diameter, outside diameter, tooth thickness, and the space width, given that the tooth proportions are standard 14 Brown and Sharpe. 2. A gearset has the following parameters: diametral pitch = 8, pressure angle = 20°, 19- tooth pinion meshed with 37-tooth gear. Find the gear ratio, circular pitch, base pitch, pitch diameters, center distance, addendum, dedendum, whole depth, clearance, and the outside diameters.
Two straight-toothed bevel gears mesh with a shaft angle of 90° and a diametral pitch of 5. The pinion has 20 teeth, and the gear ratio is 2:1. The addendum and dedendum are the same as for 20 stub teeth. For the gear, determine the pitch radius, cone angle, outside diameter, cone distance, and face width.
02/ The following data relate to a pair of 20° involute gears in mesh: Module 6 mm, Number of teeth on pinion = 17, Number of teeth on gear 49; Addenda on pinion and gear wheel = 1 module. Find 1. The mumber of pairs of teeth in contact ; 2. The angle turned through by the pinion and the gear wheel when one pair of teeth is in contact, and 3. The ratio of sliding to rolling motion when the tip of a tooth on the larger wheel (i) is just making contact, (i) is just leaving contact with its mating tooth, and (i) is at the pitch point.