Terror Twins Steve and Phil are playing on a very large merry-go-round coated with ice (frictionless). mSteve =mPhil 47.6 kg. The merry-go-round is spinning at a constant rate of revolution as the Terror Twins ride on it. Steve sitting 2.00 m from the center and must hold on to one of the metal posts with a horizontal force of 80.0 N to keep from sliding off. If Phil is sitting at the edge 4.00 m from the center, with what force must he hold on to keep from falling off?

Terror Twins Steve and Phil are playing on a very large merry-go-round coated with ice (frictionless). mSteve =mPhil 47.6 kg. The merry-go-round is spinning at a constant rate of revolution as the Terror Twins ride on it. Steve sitting 2.00 m from the center and must hold on to one of the metal posts with a horizontal force of 80.0 N to keep from sliding off. If Phil is sitting at the edge 4.00 m from the center, with what force must he hold on to keep from falling off?

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter6: Motion In Two Dimensions

Section: Chapter Questions

Problem 3STP

See similar textbooks

Similar questions

A puck of mass m = 1.50 kg slides in a circle of radius r = 20.0 cm on a frictionless table while attached to a hanging cylinder of mass M = 2.50 kg by means of a cord that extends through a hole in the table. What speed keeps the cylinder at rest in m/s? M Lütfen birini seçin: O A. 1.81 ОВ. 193 O C. 1.27 O D. 1.45 O E. 1.32
Casting of molten metal is important in many industrial processes.Centrifugal casting is used for manufacturing pipes,bearings, and many other structures. A cylindrical enclosureis rotated rapidly and steadily about a horizontal axis, as inFigure P7.62. Molten metal is poured into the rotating cylinderand then cooled, forming the finished product. Turningthe cylinder at a high rotation rate forces the solidifying metalstrongly to the outside. Any bubbles are displaced toward theaxis so that unwanted voids will not be present in the casting. Suppose a copper sleeve of inner radius 2.10 cm and outerradius 2.20 cm is to be cast. To eliminate bubbles and givehigh structural integrity, the centripetal acceleration of eachbit of metal should be 100g. What rate of rotation is required?State the answer in revolutions per minute.
stops in 1.5 s. What is the magnitude of the friction force on the disk? 49. A 200 g, 20-cm-diameter plastic disk is spun on an axle through its center by an electric motor. What torque must the motor supply to take the disk from 0 to 1800 rpm in 4.0 s?
Sem owa Senior gh School Series Tee of Caar Pa t m t What is the rate of revolution [in revolutions per minute (or rpm)] of a centrifuge if a particle that is 5.0 cm away from its axis of rotation is accelerated by a rate of 1 500 g? 2362 rpm 4727 rpm 8 326 rpm 10 259 rpm STIT A Sebastian G. is presenting
A body is being spun by a piece of string in a horizontal circle of radius 2.50 mon a flat, frictionless surface. It spins at a rate of 3.5 rev/s. If the tension in the string is 3.0 kN, what is the mass of thebody (in kg) being spun? answer: 2.5kg
In an amusement park ride called ‘The Roundup’, passengers stand inside a 18-m diameter rotating ring. After thering has acquired its final speed of 14 rpm’s, it tilts into a vertical plane. Whatweight does the rider feel at the top and bottomif they have a weight of 830 N?
trd A QUESTION 28 One end of a 1.0 m long string is fixed; the other end is attached to a 2.0 kg stone. The stone swings in a vertical circle, passing the bottom point at 4.0 m/s. The tension force of the string at this point is about: OA. 52 N OB. 20 N OC. 32 N OD. 12 N ΟΕ. Ο Ν QUESTION 29 The velocity of a particle moving along the x axis changes from vi to vf. For which values of v; and vy is the total work done on the particle positive? OA. vi=-5m/s, vf=-2m/s O B. v¡ = -2m/s, vf=-5m/s O C. v¡ = 5m/s, vf=2m/s O D. v¡=-5m/s, vf=2m/s OE. vi 5m/s, vf=-2m/s and Submit to save and submit. Click Save All Answers to save all answers. MacBook Air S
Two bugs, Buzz and Crunchy, are siting on a spinning disk on a horizontal plane. Buzz is sitting halfway and Crunchy is sitting at the outer edge as shown. The radius of the disk is 0.80 m and the disk is rotating with an angular speed of 38 rpm. The coefficient of friction between the bugs and the disk are us = 0.80 and uk = 0.60. What is the magnitude of the friction force on Buzz, in Newtons? Buzz has a mass of 2.0 kg (I know, a big bug!). Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. Crunchy
You tie a small 68.0-g pebble to a string and start spinning it in a horizontally-oriented circle at a speed 0f 3.45 m/s. The pebble takes 0.750 s to complete one full revolution. Determine the angle the string is making with the vertical and the tension in the string.
A turbine is spinning freely at 3600 rpm. It takes 10 min to coast to a stop due to friction in the bearings. How many revolutions doe the turbine make while stopping?
A. A 15.0 kg child is riding a playground merry-go-round that is rotating at 40.0 rev/min. What centripetal force (in N) must she exert to stay on if she is 1.00 m from its center? B. What centripetal force (in N) does she need to stay on an amusement park merry-go-round that rotates at 3.00 rev/min if she is 7.00 m from its center?
nd 4. A 22.0 kg child is riding a playground merry-go-round that is rotating at 40.0 rev/min. What centripetal acceleration does she experience to stay on if she is 1.25 m from its center? a = 5. The driver of a 1000-kg car tries to turn through a circle of radius 100 m on an unbanked curve at a speed of 16.0 m/s. The kinetic friction coefficient between the tires and slippery road is u = 0.25. First calculate (a) the magnitude of friction and (b) centripetal force required to make the circular turn. (c) C the driver make the circular turn without slipping?