The bearing is subjected to radial load of 7535 N, the desired life of the bearing is 170 million of revolutions at 425 rpm. When equivalent load of 16.964 kN is acting, Find the suitable axial load by taking factors. X-0.75,Y=2.5,V=1 Select one: O a. 467.5 kN O b. 6823 N O C. 4525 N O d. 84.765 N

The bearing is subjected to radial load of 7535 N, the desired life of the bearing is 170 million of revolutions at 425 rpm. When equivalent load of 16.964 kN is acting, Find the suitable axial load by taking factors. X-0.75,Y=2.5,V=1 Select one: O a. 467.5 kN O b. 6823 N O C. 4525 N O d. 84.765 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Related questions

Q: Example: Determine the value of P, if the load W= 800 N.

Q: The cable supports the three loads shown in (Figure 1). Take P - 400 Ib, P. - 280 lb Part A…

Q: A vertical rod of length L and diameter dis fixed at its upper end and carries a load Wat its lower…

A: Write the torsion equation for the rod. TJ=GθL Here, J is the polar moment of inertia, and G is the…

Q: Q2-a) determine the advantages of power screw. h b-A shaft is to transmit 50 KW at 1200 rpm.. The…

Q: Question 1: 1. The figure shows two steel shafts connected by a steel pipe with interference.…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: Round cross-sectional bar, has a diameter of d= 29 mm cut from an AISI 1030 Hot Rolled steel. The…

A: Given : diameter d = 29 mm AISI 1030 Hot Rolled Steel To find : Corrected Endurance Limit = ?

Q: Determine the magnitude of the pin force at A. Modification: Change the load to 3,50 Ibs, the…

Q: A thrust washer has an inside diameter of 12.7 mm and an outside diameter of 76.2 mm. For an…

A: This problem is related to the basic machine design . Allowable bearing pressure =(axial load/Cross…

Q: A cover of a boiler shall be fastened with 6 studs. The pressure in the boiler is 40 bar. The…

A: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The dynamic load on a body can be determined by multiplyingthe static load by an impact factor. True…

A: The expression of the dynamic load is given by, Here, WD is the dynamic load on the body, W is the…

Q: M20 × C4 bolt of mild steel is having yield stress of 320 MPa and factor of safety 3. The safe…

A: Given Data⇒ Bolt dimensions :(M20×C4) Diameter of bolt will be (d)=20 mm=0.020 m Yield stress σy=320…

Q: A) Explain 1) Different types of Keys 2) Interference fit 3) Couplings.

A: (1) In this case, we will answer the all subparts (up to 3) of the part A. Please resubmit the…

Q: 5. A steel hollow tube is used to carry a tensile load of 500 KN at a stress of 140 Mpa. If outside…

A: Given data: F=500 kNσ=140 MPado=10t Need to determine the thickness of the tube.

Q: Determine the critical load for a pinned-end col- umn made of a circular bar of SAE 1020 hot-rolled…

A: Given Length, L = 800 mm Diameter, d = 20 mm For SAE1020 Young's modulus, E = 205 GPa Find…

Q: (a) Explain FIVE (5) factors that may influence the optimum column design under an axial compressive…

A: (a) A beam under axial compressive load can fail by two modes, one is by bending and the other is by…

Q: A flange coupling with bolt circle of 250 mm uses 8 bolts, 25 mm diameter, the torque transmitted is…

A: Given Data The diameter of the bolt circle is D=250 mm. The number of bolts are n=8. The diameter…

Q: Round cross-sectional bar, has a diameter of d= 32 mm cut from an AISI 1030 Hot Rolled steel. The…

Q: e weight of the pulley is 100 N. The dian aft at bearings B, and B, is 10 mm and etively. The load…

Q: SITUATION III. For Items 13-14. Refer to figure 7. 60 kips The cast iron block with cross-sectional…

Q: Q31 A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside…

Q: Determined as the lowest load considering all of the allowable compressive load of spar, shear…

A: Considering the spar, Compressive force = P Let the diameter of spar = D The allowable compressive…

Q: 12mm 012122LM12(P1.75)"16L 122mm/4.8in Thread pitch:1.75mm 1.75mm M12*1.75 16mm

Q: The simplest truss consists of two rods and is loaded by a force. F Given: angle a=64°. Cross…

A: Find the largest force Given data:- Yield strength = 270 Mpa Factor of safety = 2.2

Q: b) Determine the maximum gas pressure and the dimensions of cross -section of the connecting rod for…

Q: Required information A steel tube with a circular cross section has an outside diameter of 310 mm…

Q: The life of a ball bearing at a load of 10 kN is 8000 hours. Its life in hours, if the load is…

Q: Q: compute the total elongation caused by an axial load of 100KN applied to a circular bar, tapering…

A: Given:P=100 KNL=10 mD1=40 mmD2=120 mmE=200 GPa

Q: (b) (c) Example: Determine the value of P, if the load W= 800 N. W

A: We will draw FBD from Pulley D to A. At A, we will equate the tensions in rope with the force W. FBD…

Q: Using Stiffness Method, Only construct the global stiffness relationship (Q -K D). Assume0 is free…

A: Given: M = 20 kN.m P = 10 kN To find: Global stiffness matrix: Q = K.D Free body diagram:

Q: A steel rod is subjected to a reversed axial load of 180 kN. Find the diameter of the rod for a…

Q: i need the answer quickly

Q: A 51 mm diameter steel rod (E = 207 GPA) with pinned end conditions is to be subjected to an axail…

A: To find: The maximum length for it to be considered a short column. Given: The diameter of the steel…

Q: Problem 7: Analyse to determine the maximum service tensile live load force that can be supported by…

A: Calculation of diameter of hole dA=diameter bolt +side clearance =0.7+18=0.8336 in

Q: Find the load that can be lifted by applying a force of 200 N at the end of 450 mm long lever of…

A: Here we have provided data from the question, Force applied at the end of lever, P=200 N Length of…

Q: Q2/ A 3/4in-16 UNF SAE grade 5 bolt is subjected to a load of 8 kip in a tension joint. The initial…

A: d= 3/4 in= 0.75 in Load, P= 8 kip Initial bolt tension, Fi= 30 kip kb= 8 Mlbf/in km= 15 Mlbf/in To…

Q: The machine component has been fabricated using machining and is made of stainless steel (Sy= 276…

A: Given that, Given material is Stainless Steel,Syt=276 MPa,Sut=568 MPa,f=0.9Reliabilty=95…

Q: man value of axial force and corresponding stress values. an value of torque and corresponding…

Q: 8'-0" 91 006 900 lb 10'-0" B 400 Ib 68' – 0"| 48'-0" 12'-0" |

Q: 3.5. What is most nearly the maximum allowable load, F, if the factor of safety is 1.5 and the…

Q: Q1 / Find the minimum bolt diameter and the minimum thickness ofeach yoke that will support a load…

A: Write the expression for the load. Here, τ represents the shear stress, Abolt represents the area…

Q: rmly distributed l a point load of 3 cantilever.

A: Shear Force: From x=0 to x=2 SF= 3 KN (Constant) From x=2 to x= 4m at any cross section SF= 3+5x'…

Q: Q2/ A 3/4in-16 UNF SAE grade 5 bolt is subjected to a load of 8 kip in a tension joint. The initial…

Q: W is applied at an immediate point on it. If the number of coils above and below this point are 6…

A: Helical spring is one of the popular spring. In helical spring, generally a wire of circular…

Q: Solve the effective normal force on the rod CD Use units [N,mm] The mass of the load is: mk=21904…

Q: Example: Determine the value of P, if the load W= 800 N. B

Q: .1 Design a compression coupling for a shaft to ansmit 2000 N-m. The allowable shear stress for the…

Q: (2) A connecting link is as shown, except that there is a -in. radial hole through it at the center…

Q: 1. The steel valve push rod for an overhead valve engine is 4 in. in diameter and 14 in. long. a.…

Q: 5. An A-36 (Fy= 250 MPa) steel column has a length of 5 m and is fixed at both ends. If the…

A: Given that, The beam is fixed,Length of beam, L=5 m,Yield stress of beam, σy=250 MPa, Calculate the…

Q: 4. The bar below is subjected to an axial load of P. The safety factor against compressive failure…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

2 oneanh
The bearing is subjected to radial load of 7535 N, the desired life of the bearing is 170 million of revolutions at 425 rpm. When
equivalent load of 16.964 kN is acting, Find the suitable axial load by taking factors. X-0.75,Y=2.5,V=1
Select one:
O a. 467.5 kN
O b. 6823 N
OC. 4525 N
O d. 84.765 N
hp

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the Equivalent load of a self-aligning ball bearing which has a radial load of 4284.4 N and a thrust load of2559.9 N.The desired life of the bearing is 175 million of revolutions at 425 r.p.m. Assume uniform and steady load. V-1,X=0.75,Y=2.65 O a. 9997.03 O b. 12556.93 OC. 17676.74 O d. 22796.53
2. A steel shaft rotating at 600 rpm is supported by two bearings as shown. E=30 Msi, d=1.0" (inch), L₁=24.0" (inches), L=42" (inches), W₁-50 lb, Neglect the weight of the shaft. "The design is acceptable." True ? Show details. or False Diameter d W₁
An axial load of 750 N is applied to the 60-mm-di- ameter end bearing of Fig. tion of 0.20, determine the torque needed to rotate the shaft for For a coefficient of frie- A worn-in bearing surface. 30 mm 750 N M
The gear forces shown act in planes parallel to the yz plane. The force on 20 in gear A is 300 lbf. Consider the bearings at O and B to be simple supports. For a static analysis and a factor of safety of 3.5, use both the DET and 16 in the MSST to determine the minimum safe diameter of the shaft. 10 in Consider the material to have a yield strength of 60 ksi. Gear A Solution: 24-in D. Gear C 10-in D. 20°
The induced nominal stress in a machine member is 28 N/mm? and the value of maximum stress near the irregularities is 61N/mm?, the value of stress concentration factor is SCF, K = Bearings are designated by a standard number internationally, the first digit in the bearing number 6409 represents type of the bearing. Select one: O True O False The value of curvature correction factor k; will be . if the spring index is 6. O a. 1.33 O b. 1.08 O c.0.,92 O d. 4.00 The figure below shows the components of normal forces, the value of radial force on the gear wheel due to a tangential force of 642 N is . N, Take pressure angle as 1420. Pitch point P. Gear driven 02 The radial force is
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M
Two equal gear wheel of 360 mm p.c.d and 6 module are in mesh if the pressure angle 20 determine the maximum addendum necessary if there are always to be at least two pairs of teeth in contact . if the gear wheels rorates at 110 r.p.m and 6 kw is being transmetted find the normal force between the teeth assuming that the total force is dividing equally between the two pairs of teeth Neglect the frection. (Ans 6.8mm , 1.54KN .)
The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys Band Care as shown. Take a = 1.4 m, b= 0.9 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 300 N. m 200 N. m 45 mm 44 mm 40 mm Im Determine the angle of twist between Band C. The angle of twist between Band Cis|
An 02-seris single-row deep-groove ball bearing with a 90 mm bore (C0 = 62 kN, C10 = 95.6 kN) is loaded with a 4.34 kN axial load and a 10 kN radial load. The inner ring rotates at 600 rpm (v=1). What is the FaC0? Should X1/Y1 or X2/Y2 be used to caculate the equivalent radial load? Determine the equivalent radial load experienced by this bearing. What is the bearing’s in-use reliability, assuming a design life of 2*10^8 revolutions and an application factor of 1.2?
find the bearing stress between bolts and plate 10/-.. 5. 1) 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 1O MM ------- -O- O 300mm 8 mm
The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the magnesium and steel sre Tallow mg =45Mpa ve Tallow st=72MPa, respectively. The shear modulus of elasticity for Am1004-T61magnesium alloy is 18Gpa and for A-36 steel is 75Gpa. a)Determine the maximum allowable torque that can be applied at A. b)Find the corresponding angle of twist of end A.
A Shaft, as shown in figl's, is Subjected to el bending load of 3N, pure torque of anxial pulling torce of 15KN stressescalculate the stressos at ans B. 13KN SammDia 15KN 1000 N-m 250mm